User manual PHILIPS MICRO HI-FI SYSTEM WITH 3 CD CHANGER-INCREDIBLE SOUND MC45

[. . . ] To change a fuse in this type of plug proceed as follows: 1 Remove fuse cover and fuse. 2 Fix new fuse which should be a BS1362 5 Amp, A. S. T. A. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. [. . . ] TM The clock digits for the hours flash. 2 Turn VOLUME to set the hours: clockwise for hours up; anti-clockwise for hours down. TM The clock digits for the minutes flash. 4 Turn VOLUME to set the minutes: clockwise for minutes up; anti-clockwise for minutes down. 5 Press RDS/ CLOCK to confirm the time. SHUFFLE Switching on There are 3 ways to switch the set on: · press y STANDBY ON on the set and the last selected source switches on; · press SELECT SOURCE on the set and the last selected source switches on; · press CD, TUNER, TAPE or AUX on the remote control. To switch the set to standby, press y STANDBY ON once on the set (y on the remote control). · If in tape mode, press STOP·OPEN 9/ first ­ The volume level, interactive sound settings, last selected source and tuner presets will be retained in the set's memory. Note: The effect of INCREDIBLE SURROUND may vary with different types of music. 5 Press MUTE on the remote control to interrupt sound reproduction instantly. ­ Playback will be continued without sound and the display shows MUTE. · To reactivate sound reproduction you can: ­ press MUTE again; ­ adjust the volume controls 6 MC 118 / 22 page 7 TIMER, SLEEP ON CD PLAYER ICR OS YS CD TIMER PROGRA M OPEN·C LOSE SELE CT PROGRA M DBB DSC VOLU INCRED IBL SURROU E ND ME ON · OFF TIMER IR SEN SO INTER R ACTIV E SO UND · In standby or during playback, press TIMER ON·OFF on the set once (TIMER on the remote control). TM READ is displayed as the CD player scans the contents of a CD, and then the total number of tracks and playing time are shown. 4 Press PLAY·PAUSE 2; (on the remote control 2) to start playback. TM FULL is displayed if you attempt to programme more than 20 tracks. Selecting a different track · Press PREV ¡1 or NEXT 2TM on the set, (on the remote control ¡ or TM) once or repeatedly until the desired track number appears in the display. · If you have selected a track number shortly after loading a CD or in the PAUSE position, you will need to press PLAY·PAUSE 2; (on the remote control 2) to start playback. Finding a passage within a track 1 Press and hold down on PREV ¡1 or NEXT 2TM. ­ The CD is played at high speed and low volume. 2 When you recognize the passage you want, release PREV ¡1 or NEXT 2TM. ­ Normal playback continues. Note: During a CD program or if SHUFFLE/ REPEAT active, searching is only possible within the same track. 8 MC 118 / 22 page 9 DIGITAL TUNER · If the CD player cannot read CDs correctly, use a commonly available cleaning CD to clean the lens before taking the set to repair. Other cleaning methods may destroy the lens. · The lens of the CD player should never be touched! STAND ON BY MC 118 MIC RO SYS CD TEM TIMER PROGRA M Reviewing the programme · In STOP mode, press and hold down PROGRAM on the set or remote control, for a while until the display shows all your stored track numbers in sequence. SELE CT PROGRA M DBB DSC VOLU INCRED IBL SURROU E ND ME ON · OFF TIMER IR SEN SO R INTER ACTIV E SO UND REPE AT BA ND CLOCK Erasing a programme You can erase the programme by: ­ pressing STOP 9 once in the STOP position; ­ pressing STOP 9 twice during playback; ­ pressing the CD door open; · PROGRAM X RDS SHUFFLE disappears from the display. · Sudden changes in the surrounding temperature can cause condensation to cloud over on the lens of your CD player. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. · Always keep the CD compartment closed to avoid dust on the lens. · To take a CD out of its box, press the centre spindle while lifting the CD. Always pick up the CD by the edge and return the CD to its box after use to avoid scratching and dust. Tuning to radio stations 1 Select TUNER source. [. . . ] 3 Insert a suitable tape into the cassette deck and close the cassette door. 6 To stop recording, press STOP·OPEN. A ABC Tape deck maintenance To ensure quality recording and playback of the tape deck, clean parts A , B and C shown in the diagram below, after approx. 50 hours of operation, or on average once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. [. . . ]