User manual PHILIPS MX5100VR

[. . . ] E9017FD_EN. qx3 03. 8. 6 10:13 AM Page 1 AAA AAA Digital Video Disc Player Video Cassette Recorder FM/MW Radio Tuner MX5100VR R 1 1 E9017FD_EN. qx3 03. 8. 6 10:13 AM Page 2 General Information The region code for this set is 2. Since it is usual for DVD movies to be released at different times in different regions of the world, all players have region codes and discs can have an optional region code. If you load a disc of a different region code to your player, you will see the region code notice on the screen. The disc will not playback, and should be unloaded. Thank you for purchasing this Philips System. This Owner's Manual explains the basic operation of this System. [. . . ] 8 Press VCR, then STOP C to stop recording. Programming a recording (with the 'SHOWVIEW® system') R 1 2 3 4 You no longer need to tediously enter the date, programme number, start and end time. All the information needed for programming is contained in the SHOWVIEW-programming number. You can find this SHOWVIEW number in most TV listing magazines written next to the concerned programme. ShowView system Enter the entire SHOWVIEW numShowView No. ber. This number is up to 9 digits 12345 ­ ­ ­ ­ long and can be found next to the start time of the TV programme in your TV listing magazine. [e. g: 1SET=SV/V+ CORRECT=CLEAR 234-5 or 1 234 5] END=EXIT If you make a mistake, you can clear your input with CLEAR. ONCE Select ONCE, DAILY or WEEKLY DAILY WEEKLY recording with K/L. Then press B. SELECT K L CHOOSE B END=EXIT Selecting once/daily/weekly recordings Using K/L, select from the following options: 'ONCE': Recording once 'DAILY': Repeated daily recordings (Monday to Friday) 'WEEKLY': Repeated weekly recordings (every week on the same day) '- -' appears at PROG. * The programme number of the TV channel has not yet been assigned to the SHOWVIEW number. Using the numerical key pads, select the corresponding programme number (name) of the TV channel. The following message appears on the screen:'ERROR' * The entered SHOWVIEW number is incorrect. Correct your input or end with DISPLAY/STATUS/EXIT. * Check the time/date (see chapter 'Installing your video', section 'Setting the time and date'). * A daily recording was entered for the wrong day. Daily programming can only be used for recordings to be made from Monday to Friday. The following message appears on the screen:'TIMER NOT COMPLETED' * The channel is wrong. 13 E9017FD_EN. qx3 03. 8. 6 10:13 AM Page 14 Programming a Recording (TIMER) 5 The decoded data appears after confirmation. You can go back to change the data. Select the corresponding input field using B or CLEAR. Change the data with numerical key pads. 6 When all inputs are correct, press DISPLAY/STATUS/EXIT. The programming information is stored in a Timer block. Switching on 'VPS/PDC' in the 'START' input field Select 'VPS/PDC' using B or CLEAR. Press '1' to switch off 'VPS/PDC' or press '2' to switch on 'VPS/PDC'. 7 Insert a cassette with an intact security tab (unprotected). 'TIMER REC' will light up on the System. How to check, or delete a programmed recording (TIMER) 1 Press VCR, then DISC/VCR MENU. [. . . ] Replace the batteries in the remote control. Re-insert the batteries with their polarities (+/­ signs) as indicated. To completely reset the System, unplug the AC cord from the AC outlet for 5-10 seconds. Disc can't be played No return to start-up screen when disc is removed The System does not respond to the remote control Buttons do not work or the System stops responding The System does not respond to some operating commands during playback. The DVD system cannot read CDs/DVDs The System switches from DVD mode to VCR mode after 35 minutes The VCR do not record a TV program ­ Operations may not be permitted by the disc. [. . . ]