User manual PHILIPS OR T2300C

[. . . ] Always there to help you Register your product and get support at www. philips. com/welcome Question?Contact Philips ORT2300 User manual Contents 1 Safety 2 Your docking system 2 3 Introduction 3 What's in the box 3 Overview of the product 4 Know about the LCD display 5 6 6 6 6 7 8 9 9 9 9 9 10 10 10 10 10 10 11 11 12 12 12 12 12 13 13 8 Play audio via Bluetooth Switch to Bluetooth mode Connect a device Disconnect a device Reconnect a device Control play 15 15 15 15 15 16 17 18 19 20 21 22 22 22 22 9 Listen to an external device 10 Charge your devices 11 Use the sleep timer 12 Use the countdown timer 13 Adjust volume 14 Use system menus 3 Get started Assemble the AC power adaptor Connect power Power on Adjust brightness 4 Set the clock 5 Use the alarm timer Set an alarm Deactivate a preset alarm Snooze the alarm Stop the alarm Check the current software version Upgrade the software Reset the product 15 Troubleshooting 6 Listen to FM radio stations Switch to FM mode Search for a radio station automatically Search for a radio station manually Store radio stations automatically Program radio stations manually Display RDS information Adjust FM settings 23 General 23 About Bluetooth connection 23 24 General information 24 Tuner 24 Speakers 24 Amplifier 24 Bluetooth 24 25 Compliance 25 25 Care of the environment Trademark notice 25 Copyright 25 16 Product information 7 Listen to DAB radio stations Switch to DAB mode For the first time use Tune to a stored radio station Program radio stations Display DAB information Use DAB menus 17 Notice EN 1 1 Safety Read and understand all instructions before you use this product. If damage is caused by failure to follow the instructions, the warranty does not apply. • Never remove the casing of the product. [. . . ] »» The current frequency is displayed. 1 2 3 4 5 • Tune to a radio station. Press and hold PRESET until [Preset store] is displayed. Press / repeatedly to select a preset sequence number. »» The radio station is stored with the selected sequence number. Repeat steps 1-4 to program more radio stations. To tune to a stored radio station, press PRESET to access the list of stored radio stations, and then press / repeatedly. Note Search for a radio station automatically Press and hold / until [Scanning. . . ] is displayed. »» After a strong radio station is detected, the search stops and the radio station is broadcast. •• If you store a radio station with the sequence number of another one, the earlier one is overwritten. 10 EN Display RDS information Radio Data System (RDS) is a service that allows FM stations to transmit additional information. When you tune to an FM radio station that transmits RDS signals, the station name is displayed. 1 2 Tune to an RDS station. Press repeatedly to scroll through the following information (if available): • Station name • Radio text • Program type such as [NEWS] (news), [SPORT] (sport), [POP M] (pop music). . . • Stereo/Mono SOCIAL RELIGION PHONE IN TRAVEL LEISURE JAZZ COUNTRY NATION M OLDIES FOLK M DOCUMENT TES ALARM Social Affairs Religion Phone In Travel Leisure Jazz Music Country Music National Music Oldies Music Folk Music Documentary Alarm Test Alarm Adjust FM settings 1 2 3 4 Press and hold menu. To tune to a stored radio station, press PRESET to access the list of stored radio stations, and then press / repeatedly. For the first time use 1 2 3 Press SOURCE repeatedly to switch the product to DAB mode. Press / repeatedly until the [Full scan] menu is displayed. »» This product automatically stores radio stations with sufficient signal strength. »» After the search is complete, the first stored radio station is broadcast automatically. 12 EN Note •• If you store a radio station with the sequence number of another one, the earlier one is overwritten. Tune to a station manually With this feature, you can tune to a specific channel/frequency manually. In addition to antenna orientation for better radio reception, the optimal reception can also be obtained with this feature. Display DAB information The name of current DAB station is displayed. You can also view the other information. To cycle through available information, press repeatedly. • Dynamic label segment (DLS) • Signal strength • Program type (PTY) • Ensemble name • Frequency • Signal error rate • Bitrate codec 1 2 Press to access the station list. Press / repeatedly to select a station from 5A to 13F. 3 Press to confirm the option. Use DAB menus 1 2 Press and hold DAB menus. to access the DRC (Dynamic Range Control) DRC adds or removes a degree of compensation for the differences in the dynamic range between radio stations. repeatedly to toggle through Re-scan for stations Full scan is used to perform a wide range search for DAB radio stations. 1 2 Press to access the sub-menus. Press to start scanning for available DAB stations. »» After the scanning is complete, the first stored station is broadcast. 3 Press / repeatedly to select an option. (The asterisk behind the option indicates the current setting. ) • [DRC off]: No compensation applied. • [DRC low]: Medium compensation applied. [. . . ] •• Make sure that there is power at the AC power outlet. No sound •• Adjust the volume. •• When listening to an external device, make sure that the external device is not muted. No response from the product • Make sure that the power is available. [. . . ]