User manual PHILIPS PCA103CD

[. . . ] PHILIPS CD-ROM Drive User's Manual PCA103CD PCA123CD Table of Contents Chapter 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 2 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 3 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2 INSTALLING YOUR DRIVE . . . . . . . . . . . . . . . . . . . . 3 2. 1 Installing the CD-ROM Drive . . . . . . . . . . . . . . . . . . . 3 2. 2 Letting Your System Recognize the Drive . . . . . . . 5 2. 2. 1 If You Are a DOS or Windows 3. x User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2. 2. 2 If You Are a Windows 95 User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. 2. 3 If You Are an OS/2 Warp User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 3 USING YOUR CD-ROM DRIVE . . . . . . . . . . . . . . . . . 13 3. 1 Drive Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3. 2 Manually Controlling the Drive . . . . . . . . . . . . . . . 13 Appendix A A MASTER OR A SLAVE DEVICE?. . . . . . . . . . . . . 15 A. 1 IDE Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 A. 2 Setting Master and Slave Jumpers . . . . . . . . . . . . . 18 Appendix B SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Copyrights And Liabilities Copyright 1996 by Philips Electronics N. V. No part of this publication may be reproduced or transmitted in any form by any means for any purpose without the prior written permission of Philips Electronics N. V. The information in this manual is subject to change without notice and does not represent any commitment on the part of Philips Electronics N. V. [. . . ] Peligro: Radiación láser invisible al estar abierto. Evite quedar expuesto directamente a rayos láser. Desenchufe su PC de la toma de corriente antes de limpiar este producto. No use detergentes líquidos o detergentes en pulverizadores. Para limpiar, sírvase de un trapo húmedo. Las ranuras y aperturas en la cubierta del producto son aptas para la ventilación. Para prevenir que el producto se sobrecaliente, estas ranuras y aperturas no deben ser bloqueadas o tapadas. To install the drive, your PC must have a free IDE interface connector, or you must buy an IDE controller card from a computer retailer. (An Enhanced IDE controller card is required if your PC already has a one-port IDE controller). See Appendix A for a brief introduction to IDE connections. 2. 1 Installing the CD-ROM Drive Here's how to install your CD-ROM drive: 1. Adjust the Master/Slave jumpers on the back of the CD-ROM drive as necessary. (The factory default of the slave mode normally should not be changed. Remove the 5. 25" drive's drive guard as instructed by your PC manual. Slide the CD-ROM drive into the drive bay. 2 3 PHILIPS CD-ROM DRIVE USER'S MANUAL Figure 2-1 Inserting the CD-ROM Drive 5. Plug a free power connector inside your PC into the socket on the back of the CD-ROM drive. Audio Digital Analog CSM SLA 39 40 HOST Interface 1 2 Power 5V G G 12V ABCDE Red ABCDE Red Audio Cable IDE Cabel Power Cabel Figure 2-2 Back Panel Connections Note: Figure 2-2 shows the back panel of PCA123CD. It has four additional jumpers to the right of the Power connector and has only one audio (analog 4 2 INSTALLING YOUR DRIVE audio) connector, labeled "Audio. " The unlabeled jumpers on both models are for factory testing only. 6. Plug a free IDE connector inside your PC into the drive's  socket. The cable's colored edge must be aligned with the Pin 1 position. Note: If you have a sound card that has an IDE port, you can either connect the CD-ROM drive to your PC or to the sound card. You must then disable the unused secondary IDE port. See Appendix A for what a secondary IDE port is and refer to your sound card, PC or IDE controller manual for the instructions on disabling the unused secondary IDE port. If you have a sound card with a 4-pin CD-ROM audio connector, use the supplied audio cable to connect it to the drive's " " connector (the "" connector on PCA103CD). 2 5 PHILIPS CD-ROM DRIVE USER'S MANUAL 8. [. . . ] In addition, turn off the power of your PC before manually prying the disc tray open. 3. 7. Audio play/skip Stop/Eject Plays or skips a song of an audio CD Opens or closes the disc tray 14 3 A MASTER OR A SLAVE DEVICE? A Before sliding your CD-ROM drive into the 5. 25" drive bay, you have to decide whether the drive is going to and be a master or slave device by adjusting the jumpers on its back. This appendix presents some basic concepts of IDE connections to help you make the decision and describes the way to set the jumpers. A. 1 IDE Connections When you open your PC box, most likely you will see a wide ribbon cable with two 40-pin connectors stemming from a connector seat on the mother board; each of the connectors may or may not have been connected to a peripheral device. Such a cable is called an IDE cable and the connector seat an IDE port, The functionality of the cable and port is determined by an "IDE controller", either built-in on your motherboard or in the form of an add-on card. [. . . ]