User manual PHILIPS PCA82CR

[. . . ] PHILIPS CD-ROM Drive User's Manual PCA82CR PCA102CD Table of Contents Chapter 1 1. 1 1. 2 1. 3 Chapter 2 2. 1 2. 2 2. 3 2. 4 2. 5 Chapter 3 3. 1 3. 2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . 2 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 During Installation . . . . . . . . . . . . . . . . . . . . . . . . 3 During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 During Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 When Handling a Disc . . . . . . . . . . . . . . . . . . . . . . . 4 Servicing the Drive . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLING YOUR DRIVE . . . . . . . . . . . . . . . . . 5 Installing the CD-ROM Drive . . . . . . . . . . . . . . . . 5 Letting Your System Recognize the Drive . . . . 8 3. 2. 1 If You Are a DOS or Windows 3. 1 User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. 2. 2 If You Are a Windows 95 User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3. 2. 3 If You Are an OS/2 Warp User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 USING YOUR CD-ROM DRIVE . . . . . . . . . . . . . . . 17 Drive Applications . . . . . . . . . . . . . . . . . . . . . . . . 17 Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . 17 A MASTER OR A SLAVE DEVICE?. . . . . . . . . . . . 19 Chapter 4 4. 1 4. 2 Appendix A A. 1 A. 2 IDE Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Setting Master and Slave Jumpers . . . . . . . . . . 22 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 23 Appendix B Copyrights And Liabilities Copyright 1996 by Philips Electronics N. V. No part of this publication may be reproduced or transmitted in any form by any means for any purpose without the prior written permission of Philips Electronics N. V. The information in this manual is subject to change without notice and does not represent any commitment on the part of Philips Electronics N. V. [. . . ] Mai introdurre o spingere oggetti di qualsiasi tipo attraverso le fessure e le aperture poiché potrebbero entrare in contatto con zone a voltaggio pericoloso oppure con parti di circuito che possono provocare incendi o scosse elettriche. Non rovesciare mai liquidi di alcun tipo sul prodotto. x Importante Advertencia de Seguridad 1. Tenga en cuenta todas las advertencias e instrucciones marcadas en el producto. Peligro: Radiación láser invisible al estar abierto. Evite quedar expuesto directamente a rayos láser. Desenchufe su PC de la toma de corriente antes de limpiar este producto. No use detergentes líquidos o detergentes en pulverizadores. Para limpiar, sírvase de un trapo húmedo. turn off your PC power before pressing a thin bar to manually eject the disc tray (see Chapter 4) use a voltage regulator or Uninterrupted Power System (UPS) in areas where the power supply voltage varies a lot move the drive while it is operating operate the drive right after a sudden increase in temperature force the disc tray to open or close by pulling or pushing it 2 3 PHILIPS CD-ROM DRIVE USER'S MANUAL ALWAYS repeatedly open and close the disc tray for no obvious reasons insert any foreign objects into the disc tray press hard on the disc tray when it is opened expose your PC to random electrical noise 2. 3 During Transport remove any disc from the drive before the transport pack the drive in the original packing materials 2. 4 When Handling a Disc ALWAYS NEVER store a disc in its case to prevent dust contamination, scratches, bending, and other damage use a clean, soft and dry cloth to remove dust or fingerprints. Never use fluids like benzene or anti-static fluids to clean a disc handle a disc by its edges touch the surface of the write on a disc or place of the disc bend a disc place or store a disc in temperature and humidity disc a label on the surface places with high or under direct sunlight 4 2 2. 5 Servicing the Drive ALWAYS ask an authorized service technician to perform any service operations attempt to open or remove the drive casing by yourself NEVER 1 5 INSTALLING YOUR DRIVE 3 This chapter contains detailed instructions to guide you through the installation of your new CD-ROM drive. To install the drive, your PC must have at least one free IDE interface connector. If not, you need to go to a computer retailer and buy an IDE controller card (an Enhanced IDE controller card is needed if your PC already has a one-port IDE controller). See Appendix A for a brief introduction to IDE connections. 3. 1 Installing the CD-ROM Drive Here's how to install your CD-ROM drive: 1. Adjust the Master/Slave jumpers on the back of the CD-ROM drive as necessary. (The factory setting of the slave mode meets most people's needs and normally does not need to be changed. Disconnect the power to your PC and remove your PC's casing. Slide the CD-ROM drive into the mounting rails of a 5. 25" drive bay. 3 5 PHILIPS CD-ROM DRIVE USER'S MANUAL Figure 3-1 Inserting the CD-ROM Drive 4. Search inside your PC for a free power cable connector and plug it into the 4-pin connector on the back of your CD-ROM drive. Find an IDE cable that has a free connector and plug the connector into the  connector on the back of the drive. The cable's colored edge must be aligned with the Pin 1 position. 6 3 INSTALLING YOUR DRIVE DIGITAL AUDIO AUDIO DG CABLE SELECT SLAVE MASTER CSM 39 40 IDE INTERFACE 1 2 DC INPUT 5V G G 12V RGGL SL A RED RED Figure 3-2 Back Panel Connections Note: If you have a sound card, you can connect either the sound card's IDE cable (if there is one) or one of your PC's available IDE cables to this IDE INTERFACE connector. You must then disable the unused interface port in the sound card's setup program. See the user manual of your IDE controller or sound card for instructions. [. . . ] Plays or skips a song of an audio CD Opens or closes the disc tray Headphone volume control Emergency eject Audio play/skip Stop/Eject Note: Turn off the power of your PC before pressing a thin bar to manually eject the disc tray. 18 4 A MASTER OR A SLAVE DEVICE? A Before sliding your CD-ROM drive into the 5. 25" drive bay, you have to decide whether the drive is going to and be a master or slave device by adjusting the jumpers on its back. This appendix presents some basic concepts of IDE connections to help you make the decision and describes the way to set the jumpers. A. 1 IDE Connections When you open your PC box, most likely you will see a wide ribbon cable with two 40-pin connectors stemming from a connector seat on the mother board; each of the connectors may or may not have been connected to a peripheral device. Such a cable is called an IDE cable and the connector seat an IDE port, The functionality of the cable and port is determined by an "IDE controller", either built-in on your motherboard or in the form of an add-on card. This whole set of things acts as a data bridge between your CPU and devices that are designed for use with the IDE standards. IDE Cable Red Floppy Cable Primary Port Figure A-1 IDE Port and Cable on Motherboard A 19 PHILIPS CD-ROM DRIVE USER'S MANUAL 20 22 A A MASTER OR A SLAVE DEVICE IDE controllers may contain more than one port and hence contain more than one IDE cable. [. . . ]