User manual PHILIPS RI 9722

[. . . ] , 1&$172 6&/$66 INCANTO rondo INCANTO classic INCANTO de luxe INCANTO sirius Revision: 1 IURP SDJH WR SDJH , 1&$172 INCANTO easy INCANTO INCANTO rapidsteam INCANTO digital INCANTO digital SBS Revision: 5 IURP SDJH WR SDJH SERVICE MANUAL Saeco Saeco International Group All parts of the present service manual are the pro perty of Saeco International Group. The manufacturer is not responsible for any errors or omissions in t he present document. Any reproduction or unauthoris ed use of this manual without the prior written permission of the manufac turer or by contractual agreement is prohibited. INCANTO S-CLASS INCANTO rondo INCANTO classic INCANTO de luxe INCANTO sirius SERVICE MANUAL Revision: 1 Saeco Saeco International Group FEB. : 2005 All parts of the present service manual are the property of Saeco International Group. The manufacturer is not responsible for any errors or omissions in the present document. [. . . ] 3 · Removed ceramic grinder disc. Attention: · Handle with care, don't drop it Fig. 4 Saeco International Group REV. 1 FEB. 2005 Seite 5/29 8. DISASSEMBLY INCANTO S-CLASS · · Remove all the ground coffee by means of a vacuum cleaner. Clean also the openings of the three seats, by means of a small screwdriver. Fig. 5 · Turn the grinder disc counterclockwise and unhinge it. Fig. 6 · In case the coffee is pressed very hard, carefully hit the feeder auger, with the knob of a screwdriver, in order to loosen the pressed coffee Fig. 7 · Removed ceramic grinder disc Fig. 8 · Assembly in reverse order Seite 6/29 REV. 1 FEB. 2005 Saeco International Group INCANTO-CLASS 4. DISASSEMBLY · · Insert the ringnut in the same position where its been removed. Press the release button and turn it clockwise till the two reverence marks match. Fig. 1 · When attaching the bean hopper ensure, the third small dot of the adjustment knob and the reverence pin are matching. Fig. 2 Saeco International Group REV. 1 FEB. 2005 Seite 7/29 8. Disassembly of the grinder INCANTO S-CLASS · Cut the relevant clips. Fig. 1 · Remove the connectors. Fig. 2 · Remove the three screws. Fig. 3 Seite 8/29 REV. 1 FEB. 2005 Saeco International Group INCANTO-CLASS 8. DISASSEMBLY · Remove the four screws, as shown in figure 4 Fig. 4 · Remove the sensor, by pressing the anchoring tab by means of a screwdriver. . . . . . . . . . Fig. 5 · . . . . . . . . at the same time remove it from its seat. Fig. 6 · Disconnect the motor power cables. Fig. 7 Saeco International Group REV. 1 FEB. 2005 Seite 9/29 8. DISASSEMBLY INCANTO S-CLASS · Fit the rubber cap to the flange of the new grinder motor. Fig. [. . . ] Part Fault Does not function (no indicator light) Cold coffee Standby LED lights up continuously Temperature differences No froth Heating remains cold Coffee and expresso LEDs flash continuously Does not function Water instead of coffee Cause HS LED defective Electronic system defective KTY defective Electronic system defective KTY defective Electronic system defective Heating - Interruption Thermal fuse defective Heating plug connection Interruption Doser switch constantly activated / Dirt Defective doser rinse Dose quantity too low Coffee residue in dosing chamber (under-dose) Doser switch does not work Electronic system defective Heating Doser Weak coffee Fault LED (coffee beans low) lights up constantly - Brewing unit overfull - Gearmotor obstructed Coffee too strong / flows too slowly Coffee too weak / flows too fast, no froth Grinder Grinder functions until fault LED (coffee beans low) lights up (insufficient beans in bean container) Grinder does not work Grinding set too finely Grind set too coarsely Grinder motor not properly installed Grinding disc worn Water in grinder Motor defective Electronic system defective Sensor defective Gear defective Page 1/3 Saeco International Group REV. 5 FEB. 2005 6. FAULTS INCANTO S-CLASS Part Gearmotor Fault Brewing unit malfunctions - does not move to home position Cause MS defective Motor defective Motor resistor defective Loose motor connections Gear wheel defective Electronic system defective Plunger stiff Gasket of valve plug swollen (black O-ring) Gasket of plunger swollen Brewing unit Sluggish / obstructed HWS valve does not open (no water or steam dispensing possible) Water drips from steam pipe (with closed valve) Water drips from steam pipe shaft Water leakage from HWS spout Water leakage at joint Varying cup filling volume HWS system Securing tab on tea nozzle spout broken / bent Valve gasket calcified Fracture in steam pipe Defective O-ring Defective O-ring Overpressure valve does not seal / calcified Overpress ure valve More water in drip tray Dry coffee in dregs drawer / water low indicator (fault LED) Water leakage at overpressure valve threaded joint Pump Defective pump Thermal fuse defective Hairline crack in joint area Page 2/3 REV. 5 FEB. 2005 Saeco International Group INCANTO S-CLASS 6. FAULTS Part Turbine Fault Varying coffee quantity Indicator signals need for deaerating with water tank sufficiently full. Water low indicator lights up (although water tank is not empty) Cause Turbine calcified / other deposits Hall sensor defective Connections oxidised Float not watertight Float jammed Magnet in float too weak Electronic system defective ATTENTION: A defective temperature sensor (KTY) may be responsible for an unexplained functioning mode. Saeco International Group Float REV. 5 FEB. 2005 Page 3/3 CHAPTER 7 FAULT DIAGNOSIS Page 1. [. . . ]