User manual PHILIPS SBCRU930

[. . . ] Table of Contents Taking a First Look The Batteries The Appliance The Touch Screen Using ProntoNEO Activating the ProntoNEO Operating Devices Working with Modes Adjusting the Settings Defining the Brands of Your Devices Learning Commands Recording Macros NEOedit Maintaining ProntoNEO Important Notices Cleaning ProntoNEO FAQ Troubleshooting General Problems Programming Problems Specifications Table of Brands Index 2 3 4 5 6 6 8 10 11 15 18 21 25 27 27 27 28 29 29 30 31 32 38 User Manual 1 Taking a First Look ProntoNEO is an Intelligent Remote Control that can be used for virtually all audio and video devices that understand infrared (IR) remote control signals. Its easy-to-use LCD touch screen and its intuitive interface make it a perfect remote control for every user. In the memory of ProntoNEO, IR codes are stored to activate different brands for all kinds of video and audio devices. ProntoNEO is set up by default to operate with Philips and compatible devices. [. . . ] ProntoNEO returns to the code set screen where the incorrect code set is displayed. 2 Look up the correct code set and repeat instructions 6 and 7. User Manual 17 Using ProntoNEO Learning Commands If an IR code or a brand is not in the database, you can program ProntoNEO commands by transmitting IR signals from your existing remote controls to ProntoNEO's learning eye. To do this, place ProntoNEO and the device's remote control on a flat surface, 1 to 4 inches (2 to 10 cm) apart. 1 to 4 inches (2 to 10 cm) To learn commands from other remote controls, ProntoNEO has to be in Learn mode. Switching to Learn mode is only possible from a specific device, not from the Device Overview. Per device you can learn all soft and hard buttons on the ProntoNEO, except for: · the Backlight button; · the Page Up and Page Down buttons; · the Mode button; · the Device button. The Learn Sequence 1 Set the ProntoNEO in Use Mode. 3 Press and hold the Mode button for 3 seconds. The Mode screen appears. User Manual 18 Using ProntoNEO 4 Tap Learn on the Mode screen. `Learn' and the label of the selected device appear at the top of the touch screen. 5 Use, if necessary, the Page Up or Page Down button to go to the next button you want to learn. 6 Press the soft or hard button you want to learn on the ProntoNEO. The Learn label changes to Learning, which means ProntoNEO is ready to receive commands from an existing remote control. The ProntoNEO will wait for 5 seconds to receive an IR code from another remote control. Note When a hard button is pressed to learn, there is no on screen feedback to indicate which button is pressed. 7 Press and hold the button on the existing remote control you want to learn to the ProntoNEO. When the ProntoNEO receives an IR code: · You hear a confirmation beep; · The label changes from Learning to OK. The Learn sequence has been successful. User Manual 19 Using ProntoNEO When the ProntoNEO does not receive an IR code in 5 seconds: · You will hear an error beep; · The label changes from Learning to Failed. The Learn sequence has failed. · ProntoNEO will return to Learn mode. Return to step 5 of the Learn sequence to relearn the button. Tip You do not have to wait for the OK or Failed to disappear. If you press another button (soft or hard button), the ProntoNEO Learn sequence immediately goes back to step 5. 8 Go to other pages of the selected device with the Page Up and Page Down buttons. Repeat steps 6 and 7 until you have copied all the commands of the existing remote control. 9 Press Done when you have finished learning commands to the buttons of your choice. You can try out the new IR codes or select another device to learn. User Manual 20 Using ProntoNEO Recording Macros A macro allows you to send a sequence of commands using one single button. You can for instance, switch on your TV, turn to a movie channel and prepare your VCR for recording by rewinding the videotape. All this can be done be pressing a single button on your ProntoNEO. To record macros, ProntoNEO has to be in Macro mode. [. . . ] · Disconnect other equipment connected to the serial ports, e. g. · Plug the serial cable in another serial port. · Try to connect multiple times. Programming Problems Buttons are not sending the correct commands · Check if you have defined the correct brands for your devices. See `Defining the Brands of Your Devices' on p. [. . . ]