User manual PHILIPS SBCRU950

[. . . ] SBC RU950 Home Theatre Control Panel User Guide Benutzeranleitung Mode d'emploi Gebruiksaanwijzing Guía del Usuario Safety & Regulations Regulations according to R&TTE English Hereby, Philips Consumer Electronics, Remote Control Systems, declares that this Pronto NG is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Philips Consumer Electronics, Remote Control Systems vakuuttaa täten että Pronto NG tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart, Philips Consumer Electronics, Remote Control Systems dat het toestel Pronto NG in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Par la présente, Philips Consumer Electronics, Remote Control Systems, déclare que l'appareil Pronto NG est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. [. . . ] The second Settings Page appears again without calibrating the touch screen. Note If the calibration fails, an message appears and you can follow the procedure to calibrate the touch screen again. User Guide 33 Using the Power Features Creating and Editing Macros A macro allows you to send a sequence of commands when tapping one single button. You can for instance switch on your TV, turn on a movie channel and prepare your VCR for recording by rewinding the videotape. The action list can be created and edited in the Macro Tool. Note Once you have programmed a macro, the button actions will not be changed when you select another brand in the Brand Tool. In the Macro Tool you first have to select the button, that will contain the macro, also called the target button. Then, one by one, you create an action list by adding actions to this target button. You can do this by: Selecting another button and adding its actions to the action list of your target button. After creating the macro, all actions you added to the action list are executed when you tap the button. Creating a Macro 1 Tap and hold the Pronto NG icon in the upper left corner of the touch screen for 3 seconds. 4 Navigate to the Device and the Page that contains the target button you want to use for a macro. 5 Tap the button you want to select as a target button. If you can use the button to program a macro, the `Macro' screen appears. -orIf you cannot use the button to program a macro, you hear a Failure beep. User Guide 34 Using the Power Features Note You can assign a macro to most buttons of your Pronto NG. The hard buttons on the left side of Pronto NG (Backlight, Page Up and Page Down) are fixed. The Toggle and Home button (around the cursor) can only be reprogrammed with ProntoEdit NG. Please refer to `ProntoEdit NG' on page 49. To add an action to the action list 1 Tap in the `Macro' screen. 2 Navigate to the Device and the Page that contains the button you want to add to the macro. 3 Tap the button with the action(s) you want to add to the macro. The name of the selected button is added at the bottom of the Action List. The macro will execute all the actions that are assigned to this button. 4 You can select other buttons to add to the macro. EN To add a delay to the action list You can add a delay to the action list e. g. to insert a short pause between turning on a device and sending commands to it, allowing the device to warm up. The `+' button and `-' button appear on the two middle firm keys below the touch screen. 2 To increase the delay, tap (and hold) the firm key labelled `+'. -orTo decrease the delay, tap (and hold) the firm key labelled `-'. Note You can still change the delay later on. To add a beep to the action list To determine when the macro execution is finished, it is useful to add a beep as final command in the action list. [. . . ] This is called a `mode animation'. Device template Firm key Hard button IR IR code Label LCD LCD backlight Light sensor Link Macro Mode animation User Guide 62 Glossary Page Page animation A page of a device is the area of 320 by 240 pixels on Pronto NG's touch screen containing buttons or other objects. When you switch from one page to another, the first page slides out of the screen and the second page slides in the screen. Pronto NG is a universal remote control with a touch screen. You can customise and fully configure Pronto NG to your personal needs: the devices you want to operate, the functions you want to perform and the layout on Pronto NG. [. . . ]