User manual PHILIPS SBCSC477

[. . . ] Do not use the set in moist places or close to water. Do not expose the set to extreme heat or light. Help line 2 General 4 Important information 4 Product illustration on inside flap 5 Getting the baby monitor ready 6 Monitoring your baby 8 Using the family intercom system 9 Explanation of features 11 Problem solving 12 Technical specifications 13 Resetting to default factory settings 14 1 2 3 4 5 night light button night light TALK button battery check light lights red when battery power is low DECT system check light blinks red: connection not OK lights red: no connection for more than 2 minutes, the system check alarm on the Parent Unit beeps blinks green: searching for connection blinks green fast: transmitting sound lights green: connection OK loudspeaker microphone MONITOR / INTERCOM power on switch battery compartment cover DC power supply socket AC power adapter 12 sound-level lights 13 battery check light lights red when battery power is low 14 DECT system check light blinks red: connection not OK lights red: no connection for more than 2 minutes, the system check alarm on the Parent Unit beeps blinks green: searching for connection blinks green fast: transmitting sound lights green: connection OK 15 TALK button 16 microphone 17 loudspeaker 18 POWER button Single Point Control 19 mode switch selects Parent Vol(ume), Baby Vol(ume) and Baby Sensitivity 20 up (+)/down (-) adjusts sensitivity and volume of selected unit 21 charging base 22 charging light 23 DC power supply socket 24 AC power adapter 25 belt clip 26 battery compartment cover Getting the baby monitor ready Baby Unit For your convenience the Baby Unit can be mains or battery operated. 1 Connect the AC power adapter (11) to a mains socket and the cord to the DC power supply socket (10) of the Baby Unit. [. . . ] > The sound-level lights (12) on the Parent Unit give visual feedback about the setting for approximately 3 seconds. 0 lights = minimum level 5 lights = maximum level (continuous transmission) Note: When set to maximum level (continuous transmission), the Baby Unit monitors continuously and all sounds, regardless of level, can be heard on the Parent Unit. Battery operating time may decrease to approximately 8 hours during continuous transmission. Note:You can only change the Baby Unit sensitivity if the connection between the Baby Unit and Parent Unit is established Using the family intercom system Talking back to comfort your baby 1 Set up both units to MONITOR your baby's sounds. 2 Adjust the loudspeaker volume level of the Baby Unit, using the Single Point Control switch and buttons, to a level you prefer. 3 On the Parent Unit, press and hold the TALK button (15) and talk clearly into the microphone. While the TALK button on the Parent Unit is being pressed, no sounds from the Baby Unit can be heard on the loudspeaker of the Parent Unit. Note: Wait with talking until the system check light is blinking green. Note: In case the loudspeaker volume of the Baby Unit is set to 0 the system check light will light red, while pressing the TALK button. Your SBC SC477 is suited for use as a two-way intercom. 4 Adjust the loudspeaker volume level of the Baby Unit to a level you prefer. 5 Adjust the loudspeaker volume level of the Parent Unit to a level you prefer. 6 On the Parent Unit, press and hold the TALK button (15) and talk clearly into the microphone. Note: Wait with talking until the system check light is blinking green. Note: In case the TALK button is pressed on the Parent Unit, and the loudspeaker volume of the Baby Unit is set to 0, the system check lights will light red. 8 On the Baby Unit, press and hold the TALK (3) button and talk clearly into the microphone. 9 Release the TALK (3) button when you are finished. While the TALK button on either unit is being pressed, a signal from the other unit cannot be heard. In other words, only one person should speak at a time. > The sound-level lights (12) visually alert you to baby's sounds. The more sound your baby makes, the more lights light. Check that the DECT system check light (14) on the Parent Unit lights continuously (green) to confirm that the connection between both units is reliable. [. . . ] personal preferences need to be set again. Factory default settings are: - Parent Volume: 3 lights - Baby Volume: 3 lights - Baby Sensitivity: 3 lights In case you have any questions about the SC477, please contact our helpline for assistance!You can find the number in the list on page 2. Before you call, please read this manual carefully. [. . . ]