User manual PHILIPS SCD499

[. . . ] This Philips Avent baby monitor provides round-the-clock support by ensuring you can always hear your baby clearly without any distracting noise. The DECT technology guarantees zero interference from other wireless appliances and a clear signal between the baby unit and the parent unit. 1) 1 On/off button 3 2 Temperature sensor 3 ON light 4 Volume +/­ buttons 5 PAGE button 6 Display 7 Nightlight 8 Play/stop button E 9 Lullaby button K 10 Nightlight button Q 11 Microphone 12 Adapter 13 Small plug 14 Battery compartment lid 15 Socket for small plug 16 Battery compartment B Parent unit 1 Sound level lights 2 Display 3 TALK button 4 MENU button 5 On/off button 3 6 LINK light 7 Opening for belt clip and neck strap 8 Volume +/­ buttons 9 OK button 10 Microphone 11 Loudspeaker 12 Battery compartment 13 Belt clip 14 Battery compartment lid 15 Neck strap 16 Adapter 17 Charger 18 POWER light C Display 1 Ñ° Room temperature indication 2 Q Nightlight indication 3 K Lullaby symbol 4 T Battery symbol 5 o Volume indication 6 R Microphone sensitivity indication 7 U Room temperature above temperature set in menu 8 9 10 11 I Room temperature below temperature set in menu O `No connection between units' message { `Volume level' message S Message when lullaby is interrupted D Travel pouch important Read this user manual carefully before you use the appliance and save it for future reference. , This baby monitor is intended as an aid. [. . . ] , The parent unit automatically resets to medium volume level and produces a paging alert tone. Note: If you press the PAGE button too long, the parent unit does not produce the paging alert tone. Note: If you press the nightlight button Q too long, the nightlight does not come on or go out. Tip: Switch off the nightlight when you operate the baby unit on batteries. To stop the paging alert tone, press the PAGE button again briefly or press any button on the parent unit. Lullaby function 1 Briefly press the lullaby button K on the baby unit to select one of the five lullabies available. , If you do not continue the lullaby within 60 seconds, the lullaby function switches off automatically. ) Belt clip and neck strap If the batteries of the parent unit are sufficiently charged, you can take the unit with you inside and outside the house if you attach the unit to your belt or waistband with the belt clip or if you hang it round your neck with the neck strap. This allows you to monitor your baby while you are moving around. Connecting the belt clip 1 Insert the small pin on the back of the belt clip into the opening on the back of the parent unit (1). Turn the belt clip to the left () until it locks into position (`click') (Fig. Disconnecting the belt clip 1 Turn the belt clip to the right (1) and take it out of the opening () (Fig. Connecting the neck strap 1 Insert the small pin at the end of the neck strap into the opening on the back of the parent unit (1). Turn the neck strap to the left () until it locks into position (`click') (Fig. Disconnecting the neck strap 1 Turn the neck strap to the right (1) and take it out of the opening () (Fig. Reset function This function allows you to reset the parent unit and baby unit to the default settings. You can use this function if problems occur that cannot be solved by following the suggestions in chapter `Frequently asked questions'. 11) Then immediately press and hold the volume down (-) button until the message `Reset' is shown on the display (Fig. , The unit has now been reset to the default factory settings. Default settings Parent unit - Loudspeaker volume: 1 - Microphone sensitivity: 3 - Sound alert: on - Temperature alert: on - `Temperature low' alert: 14°C - `Temperature high' alert: 30°C Note: If you press the lullaby button K too long, no lullaby is selected. Baby unit - Loudspeaker volume: 3 - Nightlight: off - Lullaby: 1 menu options Most functions can be operated on both the baby unit and the parent unit, but there are some functions that can only be set via the menu options available on the parent unit. If you press the buttons too long, they do not work. [. . . ] The parent unit may be switched on during charging. Switch off the parent unit during charging. the specified range is only valid outdoors in open air. Inside your house, the operating range is limited by the number type of walls and/or ceilings in between. [. . . ]