User manual PHILIPS SE1402B

[. . . ] Register your product and get support at www. philips. com/welcome SE140 EN Telephone Warning Use only rechargeable batteries. Charge the handset for 24 hours before use. Table of contents 1 1. 1 1. 2 1. 3 1. 4 1. 5 Important Power requirements Conformity Using GAP standard compliance Recycling and disposal Electric, Magnetic and Electromagnetic Fields ("EMF") Your SE140 Digital Cordless Telephone What's in the box?What you will also need Overview of the handset Handset display Overview of the base Settings navigation Getting started Position the base Connect the base Install and charge the handset batteries Using multipacks 3 3 4 4 5 4 4. 1 4. 2 4. 3 4. 4 4. 5 4. 6 4. 7 4. 8 4. 9 5 5. 1 5. 1. 1 5. 1. 2 5. 1. 3 5. 2 5. 2. 1 5. 3 5. 3. 1 6 Using your SE140 15 Make a call 15 Pre-dial 15 Dial one-touch numbers 1 and 2 15 Call from the phonebook 15 Call from the call log 16 Answer a call 16 Adjust earpiece volume 16 Mute 16 End a call 17 Use more of your phone Intercom Call another handset Transfer an external call to another handset Three-party conference call Voicemail Dial your network voicemail service Phonebook View and dial phonebook entries Store a number in the phonebook 2 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 3 3. 1 3. 2 3. 3 7 7 7 8 10 11 12 12 12 12 17 17 17 18 18 18 19 19 19 20 1 3. 4 13 15 5. 3. 2 Table of contents 5. 3. 3 Enter a pause in a phonebook number 5. 3. 4 Edit a number in the phonebook 5. 3. 5 Delete a phonebook entry 5. 4 One-touch keys 5. 4. 1 Dial a one-touch number 5. 4. 2 Assign one-touch keys to an entry in your phonebook 5. 5 Caller ID and Call log 5. 5. 1 Call log 5. 5. 2 View and dial from call log 5. 5. 3 Copy a number from the call log to the phonebook 5. 5. 4 Delete a call log entry 5. 5. 5 Delete entire call log 5. 6 Redial 5. 6. 1 Redial the last number 5. 6. 2 View and dial a number in the redial list 5. 6. 3 Copy a redial number to the phonebook 5. 6. 4 Delete a redial list entry 5. 6. 5 Delete entire redial list 2 20 20 21 21 21 6 6. 1 21 21 22 22 Personal settings 25 Change the ringer volume and ringtone 25 6. 2 Set date and time 25 6. 3 Switch beeps on/off 25 6. 4 Dial mode 26 6. 5 Recall mode 26 6. 6 Auto-prefix 26 6. 7 Change System PIN 27 6. 8 Reset handset 27 6. 9 Lock the keypad 28 6. 10 Unlock the keypad 28 7 7. 1 7. 2 8 Registration 28 Register a handset 28 Unregister a handset 29 Maintenance and replacement Cleaning How to replace the battery Technical data Frequently asked questions Index 23 23 23 23 23 8. 1 8. 2 30 30 30 31 9 23 10 32 34 24 24 24 11 Table of contents 1 Important Take time to read this user manual before you use your telephone. It contains important information and notes regarding operating your telephone. · The voltage on the network is classified as TNV-3 (Telecommunication Network Voltages), as defined in the standard EN 60-950. [. . . ] 2 Enter 2 digit phonebook entry number, e. g. 3 Enter the phone number you want to store. 5 Enter the next number you want to store or press to return to standby. Note · When the phonebook is empty, the display flashes 01- [blank]. · If the phonebook is full, the display flashes 20- [and current number stored]. · Cancel storing an entry by pressing at any time during the process. 5. 3. 3 Enter a pause in a phonebook number If your SE140 is connected to a switchboard, you may need to enter a pause in a stored number. This gives the switchboard time to get an outside line. A pause is normally stored after the switchboard access code (e. g. 1 When storing a number, press and hold until the display shows P. Then continue storing the number. 5. 3. 4 Edit a number in the phonebook 1 Press then press . 3 Enter the two digit phonebook number, e. g. 6 Press to return to standby. Use more of your phone 20 5. 3. 5 Delete a phonebook entry 1 Press then press . 3 Enter the two digit phonebook number, e. g. 4 Press repeatedly to delete the number until you hear a confirmation beep. 6 Press to return to standby. 5. 4. 1 Dial a one-touch number 1 Press and hold or until you hear a beep. 2 Press to return to standby. 5. 4 One-touch keys The or keys have prestored phone numbers for onetouch dialling. These numbers depend on your country and network. You can set the one-touch keys to dial numbers stored in your handset phonebook. Note The pre-stored numbers usually give you access to services offered by your network, but this depends on your country and network. Use more of your phone 5. 4. 2 Assign one-touch keys to an entry in your phonebook 1 Press . 3 Press and hold or until you hear a beep. The phonebook entry is now also stored in the one-touch key. 4 Press to return to standby. 5. 5 Caller ID and Call log If you have subscribed to Caller Line Identification (CLI), and provided the identity of the caller is not withheld, the number of the caller will be displayed. [. . . ] 1 Remove the batteries then press and hold while inserting the batteries again. The handset searches for the base and then displays all other handsets registered to it, e. g. 3 Enter the number of the handset you want to unregister. 4 Enter the system PIN (default setting 0000). [. . . ]