User manual PHILIPS SPC215NC

[. . . ] 10 In-cord microphone For talking to your meeting partner during video chatting. 11 Audio cable (SPC215NC only) ­ Grey headphone plug (n) - for connecting to the headphone socket of the pc sound card. ­ White microphone plug ( ) - for connecting to the microphone or green socket of the pc sound card. 12 Shirt clip For attaching the audio cable to your shirt. 4 1 Contents 2 Need help? [. . . ] 3 Connect the USB connector of the USB cable to the USB port of the PC / laptop. > The WebCam will now derive its power from the PC / laptop. 4 Use the clamp and the two rubber rims to attach the WebCam to your PC monitor or laptop screen or fold out the clamp and place the camera on your desk. SPC210NC W ebCam 4 5 3 4 4 5 6 3 5 Peel off the protective foil on the rear of the microphone (SPC210NC only) and attach the microphone to the PC monitor or laptop screen. 6 Connect the microphone plug to the microphone or green socket of the sound card. 10 Installation SPC215NC W ebCam EN 4 4 5 5 AUDIO OUT AU DIO IN AUDIO OU T AUDIO IN 3 3 5 Connect the headset audio cable (SPC215NC only) to the sound card of your PC / laptop. · Connect the grey headphone plug (n) to the headphone socket of the PC sound card. · Connect the white microphone plug ( ) to the microphone or green socket of the sound card. · If desired, attach the foam pads to the earphones for more listening comfort. · If desired, click the audio cable into the shirt clip and attach the clip to your shirt. 11 EN WebCam settings The Philips SPC210NC/SPC215NC video property can be changed from within an application, or independently by clicking the VProperty icon ` ' which can be found in the Windows taskbar bottom right of your screen. Most applications can show a 'live preview' video image on your monitor. Always use this option to see the effect of changed settings on your screen. General controls 1 2 1 Flickerless The Flickerless option should only be used under flickering light conditions (e. g. fluorescent or neon lamps) to prevent flickering or strangely coloured video images. If this option is used under normal lighting conditions the video image may be overexposed. 2 Region If you are using the Philips SPC210NC/SPC215NC in Europe, select '50 Hz' and if you are using the Philips SPC210NC/ SPC215NC in North America, select '60 Hz'. For Asia this setting is dependent on the local mains output. for China, select `50 Hz' and for Taiwan, select `60Hz'. For Japan the setting is region dependent. Please check your local mains output to find the correct `Region' setting. 12 WebCam settings Picture controls EN 3 4 5 6 7 8 9 0 ! 3 Full automatic control: on/off This full automatic control mode provides a very easy way to get the best out of your Philips SPC210NC/SPC215NC WebCam. Or you can choose to have maximum manual control over the WebCam settings by switching the full automatic control mode off. Full automatic control 'on' is the preferred setting for normal use. Techniques active within full automatic control mode are: ­ Automatic exposure control and automatic white balance control, to provide the best video source signal possible; ­ Automatic frame rate selection for improved WebCam sensitivity in low light conditions. 4 Brightness Brightness enables you to adjust the brightness of the displayed image or video to suit your own preference. Use the slider to find your preferred setting. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. [. . . ]