User manual PHILIPS SQM5322

[. . . ] Failure to do so can result in property damage and/or serious injury. · A minimum of two people are required for this installation. Do not attempt to install this mount alone under any circumstance. · Follow all instructions and recommendations regarding adequate ventilation and suitable locations for mounting your display. [. . . ] · This mount is equipped with a safety device that must be used whenever the mount holds a display. Not using the safety device can cause property damage, serious injury, or death. 2 Your fixed wall mount Congratulations on your purchase and welcome to Philips!To fully benefit from the support that Philips offers, register your product at www. philips. com/welcome. Designed to fit most TV brands with a focus on safety and ease of use. Includes Easy 1-2-3 installation kit, complete with: all necessary hardware for mounting on different types of walls, mounting templates and bubble level. C-UL US listed for weight capacity up to 132lbs. 3 2. 1 What's in the box. Wall mount Cotter pin Bag #1 (A) M4x12 Bolt (x4) (B) M4x30 Bolt (x4) (C) M4 Lock Washer (x4) Bag #2 (D) M5x12 Bolt (x4) (E) M5x30 Bolt (x4) (F) M5 Lock Washer (x4) Bag #3 (G) M6x12 Bolt (x4) (H) M6x35 Bolt (x4) (I) M6 Lock Washer (x4) Bag #4 (J) M8x16 Bolt (x4) (K) M8x40 Bolt (x4) (I) M8 Lock Washer (x4) Bag #5 (M) Small Spacer (x4) (N) Large Spacer (x4) (O) M6 Washer (x4) Bag #6 (P) Concrete Anchor (x6) (Q) M8x63 Lag Bolt (x6) (R) Lag Bolt Washer (x6) 2. 2 What you'll also need. ·Phillipsheadscrewdriver ·Ratchetordriverwith1/2"(13mm)socket ·Portableorelectricdrill ·1/4"(6mm)drillbitandstudfinderfordrywallinstallation ·3/8"(10mm)masonrybitforconcreteinstallation ·Studfinder 4 3 Installing your wall mount 4 In this chapter, the basic steps to get you started are described. 5 B Warning Carefully read the safety precautions in "Section 1 Important" before you install the wall mount. 6 7 3. 1 Mounting the wall plate (drywall) B Warning For safety reasons, this mount must be secured to two adjacent wood studs at least 16" apart. The studs must be capable of supporting the combined weight of the mount and display. 8 With the help of another person, place the mount against the wall and level it using the bubble guide. While another person holds the mount in place, mark four locations (two per stud) on the wall where the mount is to be installed. (these marks should line up with the ones made in step 3 above using the template). Set the mount aside and drill a 1/4" (6 mm) pilot hole at each marked location. Place the mount back against the wall and secure it using the lag bolts (Q) and lag bolt washers (R) provided. 4 4 8 Once all (6) lag bolts are in place you must tighten each one. If the concrete wall is covered by a layer of plaster or drywall, the concrete anchor must pass completely through the layer to rest flush with the concrete surface. D Note 2 Determine the correct diameter bolt to use by trying one bolt each from Bags 1 - 4 of the hardware kit. Do not force any of the bolts ­ if you feel resistance stop immediately to avoid damaging your display. 6 3 4 Attach the arms to the back of your display using the bolts identified in Steps 1 and 2 and the corresponding lock washer (C, F, I, or L). You will need to use the M6 washers (O) if you are using the M4, M5, or M6 bolts. If your display has a curved or recessed back, you may also need to use a spacer (M or N). Make sure the screws are snug, but do not over-tighten. 5 5 4 1 Mounting and adjusting With the help of another person, carefully lift your display and place it on the wall plate. Do not release the display until the mounting arms have securely hooked onto the mount. 6 6 2 E Tip Carefully hook the display onto the wall plate 7 7 Use a longer bolt and spacer for displays with curved or recessed backs. Do not use the M6 washer (O) if you are using the M8 bolts (J or K). B Warning Insert the safety bar at the center of the mount to avoid having the display accidentally knocked off the mount. 3 This MUST be done in order to secure the display to the mount. NOTE: A cotter pin (included) Is used to secure the arms to the mount OR a padlock (not included) can be inserted into the hole at the end of the saftey bar to help prevent theft of your display. A small cotter pin can be used to secure your display to the mount. [. . . ] (included) 7 4 Once the tv is fitted properly on to the wall bracket, the security bar must be put into place. 8 8 5 Guarantee and service Please contact Philips directly if you have any questions in the installation process of the wall mount. Limited One-Year Warranty: Philips warrants that this product shall be free from defects in material, workmanship and assembly, under normal use, in accordance with the specifications and warnings, for one year from the date of your purchase of this product. This warranty extends only to the original purchaser of the product, and is not transferable. [. . . ]