User manual PHILIPS TU5370/BE001P

[. . . ] Power requirements : This product requires an electrical supply of 220-240 volts, alternating monophased current, excluding IT installations defined in standard EN 60-950. The electrical network is classified as dangerous according to criteria in the standard EN 60-950. The only way to power down this product is to unplug the power supply from the electrical outlet. Ensure the electrical outlet is located close to the apparatus and is always easily accessible. Telephone connection : The voltage on the network is classified as TNV-3 (Telecommunication Network Voltage as defined in the standard EN 60-950) Safety precautions : Do not allow the handset to come into contact with water. [. . . ] A battery low alert will inform you that the handset has to be recharged, if this is during a call, it will end shortly after the alert. Optimal battery life is reached after 3 cycles of full charge/discharge. Under ideal conditions, the range is up to 50 m indoors and 300 m outdoors. When reaching the range limit, the conversation will become crackly, get closer to the base station otherwise you will be cut off. To reach optimal range place the base station far from electrical appliances. Understanding the menu system From idle screen, to access the carousel menu press The carousel represents a loop of icons that gives access to the first menu level. Scroll up or down to reach the desired menu. The sub menus are listed and represented by little squares at the bottom of the display. To reach one particular sub menu scroll and validate your choice A shows the sub-menu or option you are browsing. A shows the selected sub-menu or option. Note : Certain menus are directly accessible via a dedicated key on the keypad (example the Call log ) Direct dialling 1- Take the line 2- Dial on the keypad Predialling 1- Dial on the keyad 2- Take the line The menu system Voice dialling 1- Press 2- Say the voice tag 3 English Handset Registering/un-registering an additional handset The additional handset will get full capability when it is registered to the base station*. You can register up to 8 handsets to the Onis 300 & 380 base stations. To register an additional handset Place the base station in Registration mode as follows : 1- Unplug and plug back in the mains lead 2- With the additional handset press to start the registration 3- Enter the 4-digit RC code written on the sticker placed under the base station. To un-register the handset 1- Go to Handset, validate 2- Scroll to Registration, validate 3- Scroll to Un-register handset, validate 4- Choose from the list the handset to un-register, validate 5- Enter the RC code (4-digit code) and validate * See page 1 Setting the handset sounds The ringers can be set for : - The external standard ringer for callers whose number is not stored in the phonebook or stored with no VIP settings. - The internal ringer for the intercom (if there are at least 2 handsets). To set the 3 VIP ringer types : Friends , Family and Professional : See manual Onis 300/300 Vox. Subscription to the Caller Line Identification service (CLI) needed. To set the ringer type 1- Go to Handset, validate 2- Select Sounds, validate 3- Select Ringer type, validate 4- Choose External Std ringer/Internal ringer, validate 5- Select the ringer from the list and validate To set the ringer volume on the handset There are 5 ringer volume levels. 1- Go to Handset, validate 2- Select Sounds, validate 3- Select Ringer volume, validate 4- Choose the appropriate volume level and validate NB :The vibration call Alert is only available for Onis 380 4 Handset To set the key tones & feedback tones Audio feedback heard when pressing the keys & validating a setting Resume from step 1-2 above 3- Scroll to Key and feedback tones, validate 4- Select ON/OFF and validate To set the notification beep Audio indicators heard when there is new SMS or a new message Resume from step 1-2 above 3- Scroll to Notification beep, validate 4- Select ON/OFF and validate The babysit mode This feature allows to monitor the babys room. Place the handset in the room to be monitored and you will hear the noise on the additional handset. To activate/deactivate the babysit mode 1- Go to Handset, validate 2- Scroll to Babysit mode, validate 3- Select ON/OFF and validate Note : An intercom is necessary to monitor the room (See page 6). Changing the language The additional handset default language is English. To change the language 1- Go to Handset, validate 2- Scroll to Language, validate 3- Select the language and validate Warning : Changing the language will not alter the voice prompts of the answer machine (Onis 300 Vox/Onis 380 or non-Philips base stations). Setting the display contrast To set the contrast 1- Go to Handset, validate 2- Scroll to Display contrast, validate 3- Select the appropriate level and validate Handset 5 English To set the earpiece tone 1- Go to Handset, validate 2- Select Sounds, validate 3- Scroll to Earpiece tone, validate 4- Select Standard, Trebble or bass and validate Setting the backlight (Onis 380 only) To set the backlight 1- Go to Handset, validate 2- Scroll to Backlight, validate 3- Select 10 sec, 20 sec or OFF, validate 6 Handset Intercom Using the intercom (if there are at least 2 handsets) This feature allows to make internal calls, activate babysit or transfer external calls from one handset to the other. The intercom is possible with handsets registered to the same base station. Internal call or room monitoring activation 1- Go to Intercom, validate 2- If there is only one handset it rings automatically. Otherwise select from the list the handset/base you want to call and Call The called handset/base rings 3- Take the line on the called handset/base. [. . . ] The handset has not been registered to the base station ( is not displayed). Solution Move closer to the base station and try again Register the handset to the base station (page 4) No dial tone. Check the connections The base station is not properly connected to the mains or the telephone line. is Charge batteries (page 3) Clean with a clean & dry cloth. Activate them (page 5) The charging unit is not properly Check the connection connected to the mains. [. . . ]