User manual PHILIPS VCM3305

[. . . ] The use of the correct twisted pair cable can be critical to operation, especially at larger cable lengths. Caution: Never touch the glass of the camera lens as this may cause damage. 5 Installation 1. Take the camera, system cable and monitor to the area you want to observe (with the monitor on site, you can check whether the camera covers the required area). Remark: For outdoor use protective camera housing has to be used to protect the camera from rain and snow. [. . . ] Connect the system monitor to the mains (2). After a short time the camera image will appear on the monitor screen. 2. 4. camera in 1 video audio in 2 3 4 power out VCR out aux 3 1 2 MW1999_COC_01. AI 5. 6. If necessary adjust contrast /brightness optimise the camera image. and/or colour (controls at the front of the monitor) to Hold the camera at the proposed installation position. 6 7. Check on the monitor whether the camera covers the required area (The best results are obtained when the camera is pointed slightly downwards and is not looking into a bright light source). Fasten the wall bracket (1) to the wall, or another even and firm surface. Tighten the knob (2). 1 8. 1/4" 20 UNC 3 9. 10. Loosen knob (4) and screw (5) slightly (figure below). 2 CL 66610005_302. AI 12. Direct the camera at the object or area you want to observe (8). Tighten the knob (4) and screw (5) when the camera is in position. 8 5 7 100m 200m 4 0X1 0-50m 300m 24V + 0 6 CL 66610005_303. AI 14. Check if the cable length compensation (6) selector is set to the correct length. · Direct the camera at the object or area to be monitored (6). · Tighten the knob (3) and screw (4) when the camera is in position. · Adjust the focus ring (1) of the camera lens to obtain an optimal image sharpness. If an auto-iris lens is used, connect the autoiris cable to the camera (5). Switch the system on and off to setup the camera with specific outdoor settings. 1 6 43 CL 66610005_312. AI 5 CL 66610005_313. AI Focal length of the lens The auto-iris lenses are recommended when the camera is used in environments with variable light conditions (eg. By means of the auto-iris the amount of light going through the lens is regulated. The auto-iris is DC-controlled through a 4-pole connector at the back of the camera (3). 10 8 6 4 mm > NEAR R< FA > NEAR 9 System Cable For the interconnections between the system monitor and camera 25m/75ft system cable is supplied. For an optimum picture and sound quality you should always use 4-wire dual twistedpair cable when extending the connection. The cable and plugs are available in the hobby and professional trade. Pay attention that the connectors are fixed to the cable corresponding to the figure. 2 34 5 2 34 5 2 3 45 4-5 2-3 2 3 45 4-5 2-3 CL 66610005_006. AI If the cable length between the monitor and camera is more than 200m/600ft a mains power adapter should be used (see accessories). [. . . ] Pay attention that the connectors are fixed to the cable corresponding to the figure. 2 34 5 2 34 5 2 3 45 4-5 2-3 2 3 45 4-5 2-3 CL 66610005_006. AI If the cable length between the monitor and camera is more than 200m/600ft a mains power adapter should be used (see accessories). Caution: The plugs used for the observation system have the same dimensions as standard telephone plugs. Never connect a telephone to the camera or system monitor. Tips for maintenance Cleaning You can clean the outside of the camera with a moist fluff-free cloth or shammy leather cloth. When cleaning the camera lens a special cleaning cloth should be used. [. . . ]