User manual PHILIPS VR201

[. . . ] 3 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 8 Press MENU to exit from the menu operations. 2. 8 Press MENU to exit from the menu operations. Note: If a power failure occurs, clock will lose its setting. -- 10 -- If no sound comes out You need to change the TV system for this particular channel. Change the TV system for channel 3 1 Press VCR. 3 Press PLAY or STOP to select "TUNER SET UP" then press OK/STATUS. 4 Press PLAY or STOP to select "CHANGING TUNER SET UP" then press OK/STATUS. 5 Press PLAY or STOP until information for channel 3 flashes. Only TV system indication for channel 3 starts flashing. 7 Press PLAY or STOP to select the appropriate TV system [(BG, DK, I)] so that sound comes out. 9 Press MENU to exit from the menu operations. 1Select Tuner Set Up Mode 1 Press VCR. 3 Press PLAY or STOP to select "TUNER SET UP" then press OK/ STATUS. 4 Press PLAY or STOP to select "CHANGING TUNER SET UP" then press OK/STATUS. The programmed channel information list appears with the settings of the tuned channel flashing. 7 Press MENU to exit from the menu operations. The Tuner Set Up menu appears. 5 5 5 VHF L: Starts searching from the VHF L band. VHF H: Starts searching from the VHF H band. UHF: Starts searching from the UHF band. Searching starts, STORE CHANNEL CONTINUE SEARCH and when a station is tuned in, searching stops and the CONFIRM: OK tuned frequency is SELECT: END: MENU shown on the TV. Then the following menu appears. 5 3Store Channel 5 Press PLAY or STOP to select "STORE CHANNEL" then press OK/STATUS. The programmed channel information list appears again with the settings of the newly tuned channel flashing. · If you do not want to store this station, select "CONTINUE SEARCH" then press OK/STATUS, searching starts again. Manual Channel Setting When you want to do channel setting manually, follow this procedure. 4Finish Setting Press MENU. -- 11 -- BASIS OPERATIONS Playback Make sure. . . . · Your VCR, TV and antenna are connected correctly. · The remote control operation mode is set correctly for operating your target component. · The correct colour mode is selected. (vP. 11) Recording When using this VCR, an index mark is always marked at the beginning of every recording. [. . . ] 3 Press STOP 7, then release TV. · For example, for 02, press 0 then 2. · The remote control can now operate the TV of the selected code. 2Confirm Setting Press POWER, pointing the remote control at the TV. If the TV turns on or off, your setting is completed. If not, repeat steps above, using another code. After replacing the batteries You need to reset the manufacturer's code again. Note: The buttons you can use to operate your TV are explained on pages 4 ­ 5. -- 19 -- BEFORE REQUESTING SERVICE Check the following points once again if you are having some difficulties with your VCR. IMPORTANT Periodic maintenance is required in order to maintain the VCR's continuous excellent performance. [. . . ]