User manual PHILIPS VR211

[. . . ] If you want to programme at daily or weekly intervals, press the SELECT button until 'D-DAILY' (daily intervals) or 'W-WEEKLY' (weekly intervals) appears in the display. The 'daily intervals' function can only be used for recordings to be made from Mondays to Fridays inclusive. Confirm the entries with the OK 4 5 button . The resultant data appears on the TV screen. 3 -----------------------NEXT gTIMER CLEAR gCL -/+ 0-9 D/WgSELECT OK Note: If you use VIDEOPlus+ for the first time for this TV channel, the 'SELECT PROG' line appears when you confirm the VIDEOPlus+ code. [. . . ] You can search for these code marks on the tape. Once the video recorder finds the code mark or a blank space it will automatically switch to playback. 1 Press the (Rewind) or I (Wind) button during wind or rewind, you will switch to picture scanning. If you release the buttons, the video recorder will automatically switch back to rewind or wind again. H 7 Eject a cassette: Interrupt the playback function and press the hSTOP/JEJECT button on the video recorder. Notes: Some functions switch off automatically after a while (e. g. : Pause, Still Picture, Scanning). This helps to protect the cassette and prevent unnecessary power consumption. * The picture quality will deteriorate during Picture Scanning. * With this set you can play back cassettes that have been recorded on other video recorders in the NTSC standard. This only works for television sets which are suitable for a picture frequency of 60 Hz. During NTSC-play back some special features (e. g. still picture) are not possible. button and then press the I button to select the next code mark or the H button for the previous code mark. INDEX E Note: You cannot use the function 'Index search' with recordings made on another video recorder that does not have this code mark function. 5 Eliminating picture interference/ Cleaning function 1 During playback, hold the P q button until 'TRAC' (tracking) appears in the display. Pq 2 Hold the or Pr button until the playback quality is at its best. 3 Wait a few seconds, until 'TRAC' disappears from the display. This setting will remain until you remove the cassette. 4 If horizontal lines still appear on the screen, use the Cleaning function: Cleaning function: During playback, hold the PLAY G button until 'HEAD' (video head cleaning) appears in the display. OTR - recording: If you do not want to record to the end of the cassette, press the RECORD 5 button again. The display shows at what time the recording will stop. With each subsequent press of the RECORD 5 button you can add 30 minutes to this time. You can return to the normal recording status by pressing the CLEAR (CL) button. · 7 Programming with 'VIDEOPlus+' All the information required for a programming is contained encoded in the VIDEOPlus+ code. 1 Switch on the TV set. 2 Press the TIMER k 7 Make sure that a cassette without erase protection has been loaded. Switch to standby with the STANDBY m button. A programmed recording will only function when the video recorder is switched to standby with the STANDBY m button. Note: * VIDEOPlus+ Aerial-code numbers: With this set, VIDEOPlus+ aerial-code numbers will be allocated automatically. button on the remote control. 3 Please enter the VIDEOPlus+ code (up to 9 digits) printed in your TV guide next to the start time of a TV programme. If you make a mistake, clear with the CLEAR (CL) button. VIDEOPLUS 53124---- Programming recordings manually 1 Switch on the TV set. Press the 3 With the TIMER k ONCE -----------------------D/WgSELECT CLEAR gCL 0-9 OK 4 If you want to programme at daily or weekly intervals, press the SELECT button until 'D-DAILY' (daily intervals) or 'W-WEEKLY' (weekly intervals) appears on the TV screen. The 'daily intervals' function can only be used for recordings to be made from Mondays to Fridays inclusive. 5 Confirm the entries with the OK TIMER k button you can select between the entries 'DATE' (date), 'PROG' (programme number), 'START' (start time) and 'END' (stop time). [. . . ] Confirm the adjusted frequency with the OK button. * Switching off the modulator: If you cannot eliminate picture or sound interference using the above method you can switch off the built-in modulator. You should only do this if you have connected the video recorder to the TV set using a scart cable. 'Playback via the aerial cable' is not possible when the modulator is switched off. [. . . ]