User manual PHILIPS VR665

[. . . ] If you make a mistake, clear with the CLEAR (CL) button. If you want to programme at daily or weekly intervals, press the SELECT button until 'D-DAILY' (daily intervals) or 'W-WEEKLY' (weekly intervals) appears in the display. The 'daily intervals' function can only be used for recordings to be made from Mondays to Fridays inclusive. Confirm the entries with the OK 4 5 button . [. . . ] Therefore, '-:--' appears first and only after the tape has been running for a few seconds the playing time will be shown. The playback time displayed can be incorrect when using camcorder cassettes or with cassettes made for NTSC-VHS equipment. Index search: At the beginning of each recording, the video recorder marks the tape with a code mark. You can search for these code marks on the tape. Once the video recorder finds the code mark or a blank space it will automatically switch to playback. 1 Press the Cleaning function: Cleaning function: During playback, hold the PLAY G button until 'HEAD' (video head cleaning) appears in the display. The video recorder automatically switches back to playback. Note: Some hired cassettes may have a poor picture/sound quality. This is not a fault in your set. button and then press the I button to select the next code mark or the H button for the previous code mark. INDEX E Note: You cannot use the function 'Index search' with recordings made on another video recorder that does not have this code mark function. 6 3. RECORDING Pq 1 Insert a cassette or switch the video recorder on with the button. Pr Some general notes for recording · Recording from external sources: Programme numbers 'E1' and 'E2' are provided for recording from external sources (via the EXT. 1 or EXT. 2 scart socket). OTR - recording: If you do not want to record to the end of the cassette, press the RECORD n button again. The display shows at what time the recording will stop. With each subsequent press of the RECORD n button you can add 30 minutes to this time. * Don't select another programme number on your television set, until 'OK' appears in the display of your video recorder. This can take up to one minute. How to programme a recording The video recorder needs the following information for every programmed recording: * the date on which the recording is to be made * the programme number for the TV channel * the start and stop time of the recording * 'PDC' or 'VPS' on or off The set stores all the information mentioned above in what is known as a TIMER block. You can programme up to 6 TIMER blocks, one month in advance. With 'PDC' (Programme Delivery Control) or 'VPS' (Video Programming System), the TV station controls the beginning and the length of the programmed recording. This means that the video recorder switches itself on and off at the right time even if a TV programme you have programmed begins earlier or finishes later than expected. Usually the start time is the same as the PDC or VPS time. If, however, in the TV guide, in addition to a TV programme's start time, a different PDC or VPS time is given, e. g. : '20. 15 (PDC or VPS 20. 14)', you have to enter '20. 14' as the start time exactly to the minute. If you want to enter a time that differs from the PDC or VPS time, you have to switch off 'PDC' or 'VPS'. 8 Programming with 'VIDEOPlus+' All the information required for a programming is contained encoded in the VIDEOPlus+ code. 1 Switch on the TV set. 2 Press the TIMER k 6 Finally, press the OK button. The data has been stored in a TIMER block. 7 Make sure that a cassette without erase protection has button on the remote control. been loaded. Switch to standby with the STANDBY m button. [. . . ] The frequency can be adjusted at step 2with the P r or the P q button. Confirm the adjusted frequency with the OK button. * Switching off the modulator: If you cannot eliminate picture or sound interference using the above method you can switch off the built-in modulator. You should only do this if you have connected the video recorder to the TV set using a scart cable. [. . . ]