User manual PHILIPS VSS2364/00T

[. . . ] Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: To reduce the risk of electric shock, do not remove cover (or back). Refer servicing to qualified service personnel. The exclamation mark within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. · · · · Electro Magnetic Compatibility (EMC) This equipment complies with the European rules for EMC according to EN50081-1 and EN50082-1. [. . . ] Alarm detection by means of an alarm box (optional) or by the alarm contacts on the camera. Triggering external equipment by means of an action box (optional) and/or alarm. When the picture and sound are switched off by means of the power save switch on the control panel of the monitor, the cameras continue to transmit images and sound to the VCR and slave output. In addition, several CCD cameras and accessories can be connected to the monitor by means of a four-wire (telephone) system cable. Accessories: The system can be extended by one or more system accessories or other peripheral equipment, such as: Intercom box Alarm box Action box Cameras (a maximum of four) Cable extension adapter Camera interface box Slave monitor Video printers etc. Mains supply: The monitor can be connected to a power voltage of 100-240 V ~ 50/60 Hz. The safe low-voltage (24 V _) for the camera(s) and the system accessory boxes is supplied by the monitor through the system cable. · Table of contents · Page Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Monitor Cameras VCR Extra monitor Alarm contact Cable Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Monitor System on/off Power save Brightness/Contrast Volume Talk Action Auto sequence Camera selection VCR Next camera input Doorbell Alarm Alarm programming Automatic alarm termination Premature alarm termination Alarm priority Tips for maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 g English · · · · · · · · · · · Read these instructions, before putting your system in operation. g 2 Installation When the configuration is altered, the system must be scanned again. A-4) the monitor is switched to VCR mode. The signal which is supplied at the VCR input on the back of the monitor (fig. B-2) will be shown on the monitor. Next camera input When closing the contacts of the next camera input (fig. B-6), the system switches to the next available camera (for future use). Power save By pushing the power save button (fig. A-1) the image and sound on the monitor can be switched off, thus saving power. When the system is in power save mode all the camera LED's are off and the auto (sequence) LED is on. Doorbell When the doorbell button on the optional intercom box is pushed, a buzzer will sound at the monitor, after which the picture will be switched to the corresponding camera. If the automatic camera sequence is active, it will be stopped. If the system operator does not react within 1 minute to the warning signal by pushing any button, the monitor will return to its previous status, or the automatic camera sequence will continue. Brightness/contrast With the brightness (fig. A-5) the picture can be adjusted to your personal preference or to the ambient conditions. Volume With the volume knob the sound level can be adjusted (fig. A-7). Alarm · · Talk By pushing the talk button (fig. The sound from the microphone can be reproduced by means of an intercom box (optional). An alarm will sound if: there is a break in the camera line. [. . . ] The automatic interval sequence time (auto sequence time) can be adjusted between 4 and 60 seconds on the back of the monitor (fig. In order to switch back to manual operation, push one of the camera preference buttons or the auto button. When an alarm sounds: 1) The system automatically switches to the corresponding camera input. 2) The corresponding camera LED will start to blink. 3) The built-in alarm buzzer will be audible for 15 seconds. [. . . ]