User manual PHILIPS VSS9900/00G

[. . . ] To prevent fire or shock hazard, do not expose this accessory to rain or moisture. The exclamation mark within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 2 English Intercom Box Table of contents Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Mounting the box System cable Doorbell output External power supply Volume of the loudspeaker Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Designating the box (CAMERA # switch) Box number Tamper switch active Double addressing error Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 English g Read these instructions, before putting your system in operation. g 3 Introduction Thank you for buying this accessory for your observation system. FA FA R < > NE 6 R < > NE 6 8 7 AR AR 4 4 4 5 4 4 4 4 1 2 Colour Observation Monitor 3 Colour Observation Monitor _ + auto next view Colour Observation system talk action menu CL 66610005_005a. AI 1 2 3 4 5 6 7 8 System monitor Video recorder (VCR) Slave monitor Accessory boxes (0-2 per cable) Interface box System cameras Non system camera's (CVBS) Mains power adapter The following items are included in this kit: 1 Intercom box 1 System cable (5m/15ft) 1 User manual g 4 N. O. common N. C. CL 66610005_511. AI The intercom box has a doorbell function. [. . . ] common N. C. CL 66610005_511. AI The intercom box has a doorbell function. This means that a buzzer inside the system monitor sounds when someone presses the intercom's doorbell button. When the doorbell button is pressed the monitor switches to the camera input the intercom box is designated to. The intercom box then allows you and the person near the intercom box to talk to one another. Installation Remark: When the system configuration is altered, the system monitor needs to check and memorise the configuration of the cameras and accessories connected to its inputs. This is done automatically when the power is switched on. Use the power switch to switch off, only operating the power save key is not sufficient. If switching off is impracticable, use the auto install option of the system monitor's install menu. g 5 Mounting the box 1 Loosen the screw holding the cover and remove the cover. CL 66610005_509. AI 2 Remove the circuit board 1. CL 66610005_502. AI 3 Fasten the bottom plate of the box with two screws. CL 66610005_504. AI 4 5 6 7 Fit the circuit board. Now make the connections as described below. The switch CAMERA # is set according to the camera (input) to which the boxes are designated. g 9 1 1 CAMERA # 67 8 9 5 0 43 21 Colour Observation system talk action menu _ + auto next view CAMERA # 67 8 9 5 0 43 21 FA R < > NE AR 2 2 CAMERA # 67 8 9 5 0 43 21 FA R < > NE CL 66610005_510a. AI Note: Switch positions 0 and those beyond the maximum number of inputs have no function. AR Box number This switch (BOX) informs the circuit about the accessory number when two boxes are designated to the same camera input of the system monitor. A maximum of two intercom boxes can be designated to one camera input. Switch 1 (BOX) Position 1 2 Description first box which is designated to the camera input set by CAMERA # second box which is designated to the camera input set by CAMERA # Tamper switch active On the circuit board a tamper switch secures the box. When opening the box this switch triggers an alarm on the monitor. To suppress a continuous alarm message while servicing the system, the tamper-switch override is set in the TAMPER OFF position. Caution: Don't forget to reactivate the tamper switch by switching the override to the TAMPER ON position! Double addressing error g 10 Two alarm/action boxes or intercom boxes, which are designated to the same camera input, have the same `box-number'. If the system monitor detects two boxes with the same designation and box number, it shows the following error message: DOUBLE ADDRESSING "Accessory name" INPUT X/X Change from one intercom box the BOX switch or the CAMERA # switch. Explanation: INPUT X/X the physical camera input numbers to which the double addressed boxes are connected. Operation The button on the intercom is used as (door)bell. [. . . ] Caution: Don't forget to reactivate the tamper switch by switching the override to the TAMPER ON position! Double addressing error g 10 Two alarm/action boxes or intercom boxes, which are designated to the same camera input, have the same `box-number'. If the system monitor detects two boxes with the same designation and box number, it shows the following error message: DOUBLE ADDRESSING "Accessory name" INPUT X/X Change from one intercom box the BOX switch or the CAMERA # switch. Explanation: INPUT X/X the physical camera input numbers to which the double addressed boxes are connected. Operation The button on the intercom is used as (door)bell. [. . . ]