User manual PHILIPS WAS700

[. . . ] Wireless Music Station WAS700 User manual Manuel d'utilisation Manual del usuario Benutzerhandbuch Important notes for users in the U. K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Norge Typeskilt finnes på apparatens underside. Observer: Nettbryteren er sekundert innkoplet. Den innebygde netdelen er derfor ikke frakoplet nettet så lenge apparatet er tilsluttet nettkontakten. [. . . ] ­ Avoid placing the sets close to large metal objects. ­ Adjust the location of your Center and Station according to the reception status of Wi-Fi signals. ­ indicates maximum reception ­ indicates minmum reception ­ WACS700 do not support range expander devices 3 4 16 Preparation Using the remote control WAS700 is equipped with a remote control. You can use it to operate both Center and Station. ­ Remove the protective plastic tab before using the Station's remote control. ­ Always point the remote control directly towards IR area on the Center or Station you wish to operate. Using Center's remote control By default, Center's remote control works with Center only. To operate Station using Center's remote control, Press and hold REFRESH until the select screen appears on the display of Center's remote control. ­ Some functional keys on Center's remote control are exclusively used for Center (for example, CD/MP3-CD, MARK/UNMARK, MUSIC BROADCAST etc. ) To replace the remote controls' battery 1 2 3 4 Press and hold 1 as indicated. Simultaneously, pull the battery tray at 4. Remove the old battery and put a new CR2025 battery in place. Put back the battery tray. 1 2 1 3 5 CR 20 2 L IT H IU M 2 Press the navigation controls 3 or 4 and 2 to select Station CAUTION!­ Remove the battery if it is exhausted or will not be used for a long time. ­ Batteries contain chemical substances, so they should be disposed of properly. Using the navigation controls When selecting options on the set's screen, you often need to use the navigation controls 1 / 2 / 3 / 4. On Center's remote control: Display shows current status of Station after Station is connected You can use Center's remote control to operate Station now Helpful hints: ­ To operate Center using the remote control again, repeat the above steps 1-2 to select Center. ­ Center's remote control will return to its default setting (works with Center only) when you insert new batteries into it. ­ Avoid placing your Center or Station close to the plasma TV. It may resuit in improper display on your Center's remote control. 1 2 3 4 Press 3 / 4 to highlight an option. Press 1 to return to the previous option list screen. Press OK or 2 to confirm 17 English Basic functions English Switching to standby/on and selecting functions 1 When the set is on, press STANDBY-ON/ ECO POWER to switch it to standby (or y on the remote control) The screen dims out. Display shows Center Status screen and the number of centers found The Center Status screen is empty if no center is found Auto-standby When the set has reached the end of playback/ recording and remains in the stop position for more than 5 minutes, the set will switch to standby automatically to save power. Volume control 1 2 Check the playback starts. Display shows the volume bar, indicating the volume level. 2 To switch on, press STANDBY-ON/ ECO POWER on the set The set switches to the last source selected. OR On the remote control, press the source button (e. g. [. . . ] Use the WEP key when connecting your Center and Station to an existing wireless PC network. Change the operating channel of your Center and Station when connecting them to an existing wireless PC network. To learn about how to change channels, see the manual Connect to your PC If possible, change the operating channels of the other Wi-Fi devices at your home. Turn the devices in different directions to minimize interference. Remote control: When I am using the Center's 2-way remote control, it starts to show "connecting . . . . connecting" on the display endlessly. [. . . ]