User manual PHOENIX GOLD OCTANE R

[. . . ] · Optional LPL44TM Low Pass Level controller allows the driver to adjust bass volume from the driver's seat. · Optional RDDPTM Remote Diagnostic Display Panel allows the driver to monitor the amplifier's battery voltage, power-on, thermal and overload status with use of the SDTTM or RDDPTM kit. CROSSOVER FREQUENCY Controls the high and low pass crossover point symetrically for the high and low pass speaker outputs. The crossover is always engaged with a frequency adjustable from 40Hz to 800Hz with a 24dB per octave slope. INPUTS Connect preamp signal cables from the headunit to these terminals. To maximize noise rejection, we recommend using Phoenix Gold ZEROpoint Musical Reference, ZEROpoint Pro, ZEROpoint QLX, ZEROpoint TRX, XS560 or XS460 series twisted pair interconnects. STEREO/MONO SWITCH The low pass section of the amplifier will receive a mono signal when the button is set to the IN position and a stereo signal when set to the OUT position. [. . . ] YELLOW: Lights if the amplifier shuts down due to overheating. If the internal heatsink reaches 115 degrees Celsius, the amplifier shuts down and continues to run the fan at high speed until the internal temperature falls below 115 degrees. RED: Lights if the amplifier shuts down due to excessive output current. Common reasons for excessive output current are chafed speaker cables touching the vehicle's chassis, speaker leads touching each other or a damaged speaker voice coil. 160 300 BYPASS OUTPUTS Provides a full range signal for an additional amplifier or signal processor. LPL CONTROL PORT This port is for connecting the optional LPL44 TM Remote Lowpass Level Control knob. The LPL44TM allows up to 20dB of subwoofer volume adjustment from the driver's seat of the low pass section of the amplifier. 40 800 HIGH PASS SPEAKER OUTPUTS Used to connect the high pass section of the amplifier to speakers. Use the left + and right - terminals for bridged mode. Minimum speaker cable size is 16 gauge (PG# SS162 or QS162). Use 12 Gauge for bridged operation (SS122 or QS122). Minimum impedance is 2 ohms bridged or 1 ohm stereo. FREQ 160 300 L HIGH PASS SPEAKER L+ LR+ RSENS R INPUT BYPASS OUTPUT LPL MADE IN AMERICA POWER B­ B+ R 40 800 LOW PASS STEREO/MONO REMOTE CONTROL POWER LOWPASS POWER SUBSONIC FILTER LOW PASS SPEAKER L+ LR+ RBASS SENS B­ B+ R Q SELECT 6 + BRIDGED . 2 RDDP 0 + BRIDGED - 18 6 . 2 RDDP INPUT SENSITIVITY This control adjusts the amplifier's sensitivity to incoming signals. Higher signal levels allow for a lower sensitivity setting and lower overall noise floor. . 400 x 2 Minimum Speaker Load, Bridged . . 13. 00L x 29. 00W x 2. 50H Overall Dimensions . . 13. 00L x 30. 00W x 2. 50H Bass Boost Center Frequency . . 20Hz to 110Hz Bass Boost Characteristic, switch selected: Wide . . 25Hz Typical Total Harmonic Distortion . . <0. 02% Signal to Noise Ratio (A-weighted) . . ±1dB, 20Hz to 20kHz Bass Boost . . 0 to +18dB @ 45Hz Crossover Frequenty Range . . 200 millivolts to 6 volts Input Impedance . . >30 kohms Power Supply Operating Range . . 10. 0 Vdc to 15. 5 Vdc Typical Current Draw at Idle . [. . . ] Customer must pay all parts and labor charges after the limited warranty period expires. The limited warranty period for factory refurbished products expires after ninety (90) days from date of original purchase. This limited warranty applies only to purchases from authorized Phoenix Gold Electronics/Speaker retailers. This limited warranty is extended only to the original purchaser and is valid only to consumers in the United States. [. . . ]