Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PIAGGIO APE 50 ZAPC 8000. We hope that this PIAGGIO APE 50 ZAPC 8000 user guide will be useful to you.
Lastmanuals help download the user guide PIAGGIO APE 50 ZAPC 8000.
Manual abstract: user guide PIAGGIO APE 50 ZAPC 8000PARTS LIST
Detailed instructions for use are in the User's Guide.
[. . . ] Any significant changes to the characteristics of the vehicles or to specific repairing procedures will be covered in updates of this manual. Since satisfactory results cannot be obtained without the necessary equipment and tooling, we recommend referring to the pages of this manual concerning the specific equipment required and to the catalogue of specific tools. Pieces of particularly important information are identified as follows:
Note: Provides important information intended to simplify and clarify a procedure. Warning Caution
- Denotes specific procedures to be used to avoid damaging the vehicle. [. . . ] RECHARGING THE BATTERY FOLLOWING OPENCIRCUIT STORAGE 1) Checking the voltage Before installing the battery on the vehicle, measure the open-circuit voltage with an ordinary multimeter. 60 V, the battery can be installed without recharging. 5 x rating - Charging time: Recommended 10-12 hrs Minimum 6 hrs Maximum 24 hrs 3) Constant-current charging method - Initial charging current: 1/10 of rating - Charging time: Maximum 5 hrs Caution - When the battery is deeply discharged (far below 12. 6V), 5 hours’ recharging may not be enough to obtain optimum performance. In these conditions, however, to avoid damaging the battery beyond repair, it is essential not to recharge it for more than 8 consecutive hours. 4
Battery recharge Caution - Before charging the battery remove all cell plugs. Keep free flames or sparks away from the battery during recharge. When the battery has to be removed from the vehicle, disconnect the negative terminal first. Charge the battery using the specific charger 020333Y (single station) or 020334 (multiple station), by putting the charger selector on the type of battery to be recharged (use current at 1/10 of the battery rated power). Connection to the power supply must be made by means of the corresponding poles (+ with + and – with -). 4) Cleaning the battery Keep the battery clean, especially the top; coat the terminals with Vaseline. : Carefully clean the injector Tee Joint before reassembling the quick-connections. Direct the injector in such a way as to avoid any interferences of the electrical cables with the coolant and fuel pipes. - Check the engine oil level, top up if necessary with oil of the recommended type. 5-3
Front and rear suspensions Handlebar Removal - Begin by removing the radio-interphone and then disconnect the feeder cable. - Remove the digital panel support and the front and rear sections of the handlebar cover as described in Chapter 8-Bodywork. - Disengage the handlebar from the components installed on it. - Remove the two counterpoises after loosening the side screws. - Remove the pumps after loosening the screws on the clevises shown in the figure. - Slide the throttle control off the handlebar after loosening the fixing screws. - Loosen the bolt fastening the handlebar to the steering tube shown in the figure and then remove it. Remove the handlebar and the plastic support. [. . . ] - Remove the two handlebar cover lower screws (one on each side). - Remove the brake fluid pump cover on the right side. 1 2
Code 001126 001045 001049 001056 007023 005081
Description Cylinder head - Replacement Valves - Replacement Valves - Adjustment Cylinder head gasket - Replacement Union tee head outlet - Replacement Temperature sensor - Replacement
Time 250' 240'' 75' 210' 95' 80'
6
5
3 4 5
1 2-3
6
4
6 ROCKER ARM SUPPORT ASSEMBLY Op. 1 2 Code 001044 001148 Description Camshaft - Replacement Valve rocker arms - Replacement Time 90' 90'
1
2
7 CYLINDER HEAD COVER
Op. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PIAGGIO APE 50 ZAPC 8000
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PIAGGIO APE 50 ZAPC 8000 will begin.