User manual PIONEER A-Z470

[. . . ] The plug or adaptor or the distribution panel should be provided with 10 A fuse. As the colours of the wires in the mains lead of this appliance may not correspond with coloured markings identifying the terminals in your plug, proceed as follows ; The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the earth terminal of a three pin plug. NOTE After replacing or changing a fuse, the fuse cover in the plug must be replaced with a fuse cover which corresponds to the colour of the insert in the base of the plug or the word that is embossed on the base of the plug, and the appliance must not be used without a fuse cover. [. . . ] Use the MULTI CONTROL buttons to select the component. Button(s) SOURCE Function Press to switch the component between standby and on. Press to return to the start of the current track or chapter. Repeated presses skips to the start of previous tracks or chapters. Use to move back channels (channel ­). Play the reverse side of the tape on a reversible deck. Skips to the start of the next track or chapter. Repeated presses skips to the start of following tracks or chapters. Stop playback (on some models, pressing this when the disc is already stopped will cause the disc tray to open). Components CD/MD/CD-R/VCR/DVD/LD/DVD recorder/Cassette deck CD/MD/CD-R/DVD/LD VCR/DVD recorder Cassette deck CD/MD/CD-R/DVD/LD VCR/DVD recorder CD/MD/CD-R/VCR/DVD/LD/DVD recorder/Cassette deck CD/MD/CD-R/VCR/DVD/LD/DVD recorder/Cassette deck CD/MD/CD-R/VCR/DVD/LD/DVD recorder/Cassette deck CD/MD/CD-R/VCR/DVD/LD/DVD recorder/Cassette deck CD/MD/CD-R/VCR/DVD/LD/DVD recorder/Cassette deck MD/CD-R/VCR/DVD recorder/Cassette deck DVD/DVD recorder CD/MD/CD-R/VCR/LD CD/MD/CD-R/LD DVD/DVD recorder VCR/DVD recorder SUBTITLE/ Displays/changes the subtitles on multilingual DVDs. MODE Use to directly access tracks on a program source. Number buttons Use to directly access chapters on a program source. The remote displays the component you want to set. 4 Use / (cursor up/down) to switch direct function on or off then press ENTER. The display shows COMPLETE to confirm the setting. 5 Repeat steps 2­4 for as many components as you want. Note · You can't use direct function with the TUNER or TV CONT functions. DVD/LD VCR2 CD-R/ TAPE1 TV/SAT VIDEO MD/ TAPE2 VCR1 / DVR TV CONT MULTI CONTROL CD TUNER REMOTE SETUP 1 Press and hold REMOTE SETUP for three seconds. The REMOTE SETUP menu appears on the remote control display. 2 Use / (cursor up/down) to select `MultiOpe' or `SysOff' from the menu and press ENTER. If you selected Multi Operation (MultiOpe), Select Function flashes in the display. If you selected System Off (SysOff), System Off appears in the display. 3 Press the MULTI CONTROL button for the component you want to start the multi-operation. Multi Ope appears in the display. 63 En 08 Controlling other equipment 4 Use / (cursor up/down) to select a command in the sequence then press ENTER. [. . . ] 75 unbalanced Continuous Power Output Front. 100 W + 100 W (DIN 1kHz, THD 1%, 8) Center . 100 W + 100 W (DIN 1kHz, THD 1%, 8) Surround back . 100 W + 100 W (DIN 1kHz, THD 1%, 8) Rated Power Output . [. . . ]