User manual PIONEER AVIC-X3II INSTALLATION MANUAL

[. . . ] English Español Deutsch Français Italiano Nederlands MANUEL D’INSTALLATION AVIC-X3B INSTALLATION MANUAL Contents IMPORTANT INFORMATION ABOUT YOUR NEW NAVIGATION SYSTEM AND THIS MANUAL 3 IMPORTANT SAFEGUARDS PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR NAVIGATION SYSTEM AND RETAIN THEM FOR FUTURE REFERENCE 4 Connecting the System Precautions before connecting the system 5 Before installing this product 5 To prevent damage 6 Parts supplied 7 Connecting the system 8 Connecting the power cord (1) 10 Connecting the power cord (2) 12 When connecting to separately sold power amp 14 When connecting a rear view camera 16 When connecting the external video component 17 – When using the AV-1 Input 17 – When using the AV-2 Input 17 When connecting the external unit featuring video source 18 When connecting the rear display 18 – When using a rear display connected to rear video output 18 Installation Precautions before installation 20 To guard against electromagnetic interference 20 Before installing 20 Installing this navigation system 21 – Installation notes 21 – Parts supplied 22 – Installing the hide-away unit 23 – DIN Front/Rear-mount 24 – DIN Front-mount 24 – DIN Rear-mount 25 – Fixing the front panel 25 Installing the GPS aerial 26 – Installation notes 26 – Parts supplied 26 – When installing the aerial inside the vehicle (on the rear shelf) 27 – When installing the aerial outside the vehicle (on the body) 28 After Installation After Installing this Navigation System 29 2 Engb Section IMPORTANT INFORMATION ABOUT YOUR NEW NAVIGATION SYSTEM AND THIS MANUAL !The navigation features of this product (and rear view camera option if purchased) are intended solely to aid you in the operation of your vehicle. It is not a substitute for your attentiveness, judgement and care when driving. Never use this navigation system to route to hospitals, police stations, or similar facilities in an emergency. [. . . ] It is necessary to set [Camera] in [System] to [On] when connecting the rear view camera. 16 Engb Section Connecting the System When connecting the external video component When using the AV-1 Input The hide-away unit 03 English When using the AV-2 Input The hide-away unit Mini jack (AV 2) White, Red CD-RM10 (sold separately) Yellow (VIDEO IN) White, Red (AUDIO IN) Yellow RCA cables (sold separately) RCA cables (sold separately) To video output To audio outputs To video output To audio outputs External video component (sold separately) External video component (sold separately) !It is necessary to set [AV1 Input] in [System] to [Video] when connecting the external video component. It is necessary to set [AV2 Input] in [System] to [Video] when connecting the external video component. (For details , refer to the operation manual. ) Engb 17 Section 03 Connecting the System When connecting the rear display The hide-away unit CAUTION Be sure to use a CD-RM10 (sold separately) for wiring. If you use other cables, there is a case where wiring position differs, images and sounds may be disturbed. OK L V G R L: R: V: R G V G: L Left audio (White) Right audio (Red) Video (Yellow) Earth Yellow (VIDEO OUT) White, Red (AUDIO OUT) When connecting the external unit featuring video source The hide-away unit Blue To video input RCA cables (sold separately) To audio inputs Rear display with RCA input jacks Yellow (VIDEO IN) IP-BUS cable (sold separately) When using a rear display connected to rear video output WARNING NEVER install the rear display in a location that enables the driver to watch the video source while driving. rCA cable (sold separately) To IP-BUS output Black Pioneer external unit (sold separately) To video output !It is necessary to set [AV1 Input] in [System] to [EXT] when connecting the external video component. (For details , refer to the operation manual. ) This navigation system’s rear video output is for connection of a display to enable passengers in the rear seats to watch the video source. You can switch the rear screen mode in “AV MENU”. The map screen navigation images output to the rear display differ from standard NTSC format images. Therefore, their quality will be inferior to the images that appear on the front display. The navigation system automatically switches the colour system (NTSC, PAL) for each video and outputs the video on the “Rear Display”. To correctly output each type of video on the “Rear Display”, we recommend using a “Rear Display” with a function to automatically switch the colour system (e. 03 English Engb 19 Section 04 Installation Precautions before installation WARNING Pioneer does not recommend that you install or service your navigation system yourself. Installing or servicing the product may expose you to risk of electric shock or other hazards. Certain government laws may prohibit or restrict the placement and use of this system in your vehicle. Please comply with all applicable laws and regulations regarding the use, installation and operation of your navigation system. Do not install the display unit or the hideaway unit where it may (i) obstruct the driver’s vision, (ii) impair the performance of any of the vehicle’s operating systems or safety features, including airbags, hazard lamp buttons or (iii) impair the driver’s ability to safely operate the vehicle. [. . . ] Place the GPS aerial on the metal sheet. (The GPS aerial is fastened with its magnet. ) Metal sheet Peel off the protective sheet on the rear. 04 English GPS aerial Make sure the surface is free of moisture, dust, grime, oil, etc. [. . . ]