User manual PIONEER BDR-101

[. . . ] To ensure continued safety, do not remove any covers or attempt to gain access to the inside of the product. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] OBJECT AND LIQUID ENTRY - Never push objects of any kind into this product. Touching dangerous voltage points may cause a short resulting in fire or electric shock. Do not spill liquid of any kind on this product. CONDENSATION - Moisture will form in the operating section of the product causing performance to be impaired if it is brought from cool surroundings into a warmer environment. If you are moving the unit to a location with a warmer temperature, let the product stand for 1-2 hours in the new location before turning it back on. SERVICING - Do not attempt to repair this product yourself. Opening or removing covers may expose you to dangerous voltage or other hazards. Remove dust or lint from the disc with a soft cloth by wiping from the inside to the outside edge rather than in a circular motion. Do not use record-cleaning or anti-static agents as the solutions may cause damage to a disc. Always be sure to store your discs in proper DVD-R storage cases when not in use, and always be sure to check for dirt or dust on discs (especially on the recording side) before use. 25inch Half-Height built in type • LCD Tilt Servo Mechanism • Horizontal/Vertical orientation available • Low vibration Mechanism by DRA system Disc Format (Read/Write) • BD single layer/dual layer • Single Layer BD-RE (Version 2. 0) • DVD single layer/dual layer /120 mm disc /80 mm disc • DVD-R (In case of write, 650nm disc for General only. 0) • DVD-Einzelschicht/Dualschicht/120-mm-Disc/80-mm-Disc • DVD-R (Schreiben nur auf 650-nm-Disc für allgemeine Anwendungen) • DVD-R (1X, 4X, 8X Schreibgeschwindigkeit) • Dualschicht-DVD-R (DVD-R DL) • DVD-RW (1X, 2X, 4X Schreibgeschwindigkeit) • DVD+R (2, 4X, 4X, 8X Schreibgeschwindigkeit) • Doppelschicht-DVD+R • DVD+RW (2, 4X, 4X Schreibgeschwindigkeit) Note: • Specific application program(s) that support above format(s) required. € Supported media required for specific BD & DVD writing speeds. € 4 – INTERFACE FRONT VIEW VUE AVANT INTERFACE SCHNITTSTELLE VORDERANSICHT 1 Disc Tray Open the loading tray by pressing the eject button, then place a BD or DVD disc into the slit with the label facing up. Press the eject button to load the tray with the disc. Do not attempt to pull out the disc tray forcibly. During reading Lights During writing Lights 2 Voyant BUSY (occupé) L’état de fonctionnement est signalé comme suit: Pendant la lecture S’allume Pendant l’écriture S’allume 2 Besetzt-Anzeige (BUSY) Diese Anzeige kennzeichnet den aktuellen Betriebsstatus wie folgt. Während des Lesens: Leuchtet Während des Schreibens: Leuchtet 3 Ventilation Hole Do not block this part. 3 Orifice de ventilation Ne pas obstruer ces éléments. 4 Eject Button (0) To unload /load the disc, press the button. 5 Forced Ejection Hole Insert a stiff rod into the hole and push to eject the tray when the tray doesn’t unload by pressing the Eject button. [. . . ] At the time of connection, pay attention to the polarity of the cable. At this time, confirm that pin 1 of the IDE connector of the drive is connected correctly to pin 1 of the cable. Be sure to supply electrical power for this product from the personal computer which is connected to it. Do not use any other power supply than the internal one of the personal computer. [. . . ]