User manual PIONEER CDJ-1000

[. . . ] COMPACT DISC PLAYER CDJ-1000 Operating Instructions NOTE: THE NO USER-SERVICEABLE PARTS COMPARTMENT WARNING IS LOCATED ON THE APPLIANCE BOTTOM. 2 <DRB1297> En [For U. S. model] IMPORTANT NOTICE H006AEn The serial number for this equipment is located in the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. 3 <DRB1297> En BEFORE OPERATIONS Thank you for buying this Pioneer product. [. . . ] ÷ Raise the TRIM, CHANNEL FADER, and MASTER LEVEL settings appropriately so that sound is produced from CD1. 2. Press the PLAY/PAUSE button (3/8). ¶ Playback will begin immediately from the specified Cue point. Changing Playback Speed (*) Pull the Tempo Control knob towards you. Slide the knob towards you (+) to increase the tempo and slide it away from you (­) to decrease it. ¶ The rate of change in playback speed (tempo) is shown in the display. ¶ The playback speed can be changed without changing the pitch ( "Applying Master Tempo"). 1. Set the DJ Mixer's CROSS FADER slider at its left side (CH 1). ÷ Track A is heard from speakers. 7 Selecting range of tempo adjustment Press the TEMPO ±6/±10/±16/±24 button. Each time the button is pressed the variable range of the Tempo Control knob changes as follows: ±6%, ±10%, ±16% and ±24%. You can adjust as follows: at ±6% :0. 02%units, at ±10%:0. 05%units, at ±16% and at ±24%:0. 1%units. ¶ The set variable range value is indicated in the display. 2. Press the TRACK SEARCH buttons (4, ¢) on player CD2 to find and select track B. Set the DJ Mixer's MONITOR SELECTOR button CH 2 to ON. Rotate the DJ Mixer's MONITOR LEVEL so that track B can be heard from the headphones. ÷ Only track A is heard from the main speakers. 6. Set cueing for track B on the headphones. 1 With player CD2 in the playback mode, press the PLAY/PAUSE button (6) to hear the point you wish to cue. ÷ The player will enter the pause mode (Broken sound will be audible). 2 Rotate player CD2's Jog dial and search for the track's Cue point (first beat). 3 When you have settled on the Cue point, press the CUE button on player CD2. ÷ The player's sound will be muted and cueing will be completed. 7 Resetting tempo Press the TEMPO RESET button. The Tempo Reset indicator lights and the rate of tempo variation is reset to [0] (normal tempo) regardless of Tempo Control knob setting. ¶ One more press of the TEMPO RESET button cancels the reset and speed setting made with the Tempo Control knob is valid again. Applying Master Tempo (*) Press the MASTER TEMPO button during playback. The MASTER TEMPO button and the [MT] indicator light. The speed (tempo) can now be changed using the Tempo Control knob but the pitch (key) does not change. ¶ When digitally processing the sound, sound quality will change. 7. [. . . ] &WfY(&Wg?Y(&&W 'Vg?X)&W??M(&O?h?M(&&W 'Vh?K6 <DRB1297> <TSZRF 01D00000> P ONEER NEW MED A TECHNOLOG ES NC Mu med a and Mass S o age D v s on 2265 Eas 220 h S ee Long Beach CA 90810 U S A TEL 800 444 OPT 6784 P ONEER ELECTRON CS OF CANADA NC ndus a P oduc s Depa men 300 A s a e Pa kway Ma kham On a o L3R OP2 Canada TEL 905 479 4411 P ONEER CORPORAT ON ?7?ehH@J?fK)@'I?h?Y(&W?g?L@?Y7eY. W?e [. . . ]