User manual PIONEER CLD-990

[. . . ] Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer. [. . . ] You can only use the Virtual Height mode if the surround speakers are on and the FH setting is set to NO. It can also not be used when playing signals containing actual front height channel information. This mode is effective for contents with a sampling frequency of 48 kHz or less. You can't use the Virtual Depth mode when the headphones are connected to this receiver or when any of the stereo, Front Stage Surround Advance, Sound Retriever Air or Stream Direct modes is selected. You can only use the Virtual Depth mode if the surround speakers are on. En 49 09 Using other functions Setting the Video options There are a number of additional picture settings you can make using the VIDEO PARAMETER menu. The defaults, if not stated, are listed in bold. Setting STREAM (Stream Smoother) <e> What it does This improves elements that reduce picture quality mainly noticeable in network contents, such as mosquito noise and block noise. Sets the optimum picture quality for the type of monitor that is connected. Select PDP for plasma displays, LCD for liquid crystal monitors, FPJ for front projectors, PRO for professional monitors. If you want to adjust the picture quality settings to your personal tastes, select MEMORY. Reduces noise in the luminance (Y) signal. Reduces noise in the input's color (C) signal. This setting have the effect only for pictures recorded in the interlaced scan format (480i/576i or 1080i signals). d Adjustment is not possible unless V. ADJ (Advanced Video Adjust) is set to MEMORY. This setting is only displayed when the video signals below are being input: -- 480i, 576i, 480p, 576p, 720p, 1080i analog video signals -- 480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video signals f This adjustment is only possible when 480i signals are being input from the composite video jacks. If the image doesn't match your monitor type, adjust the aspect ratio on the source component or on the monitor. This setting is only displayed when 480i/p or 576i/p video signals are being input. Switching the speaker terminals If you selected Normal(SB/FH), Normal(SB/FW) or Speaker B at Speaker system setting on page 67 , you can switch between speakers using the SPEAKERS button. If you selected Front Bi-Amp or ZONE 2, the button will simply switch your main speaker terminals on or off. % Use SPEAKERS on the front panel to select a speaker system setting. As mentioned above, if you have selected Front Bi-Amp or ZONE 2, the button will simply switch your main speaker terminal (A) on or off. Press repeatedly to choose a speaker terminal option: When you select Normal(SB/FH), you can select from: !SP: SB/FH ON ­ Surround back or front height channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. The surround back and front height channels are switched automatically according to the audio input signal. SP: SB ON ­ Surround back channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. SP: FH ON ­ Front height channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. [. . . ] 1 Wireless LAN converter (AS-WL300) (CLD-990 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Warranty card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Power cord CD-ROM (AVNavigator) Quick start guide Integrated Control Section Control (SR) terminal . . . . . ø 3. 5 Mini-jack (MONO) Control (IR) terminal . . . . . . ø 3. 5 Mini-jack (MONO) IR signal . . . . . . . . . . . . . . . High Active (High Level: 2. 0 V) 12 V Trigger terminal . . . . . . ø 3. 5 Mini-jack (MONO) 12 V Trigger output type . . . . . . . . . . 12 V, Total 150 mA RS-232C cable type . . . . . . . . . . . . . . . . . . . 9-pin, cross type, female-female EXTENSION terminal . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 150 mA Note !These specifications are applicable when the power supply is 230 V. [. . . ]