User manual PIONEER CT-A9 annexe 1

[. . . ] Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer. [. . . ] The subwoofer output depends on the settings you made in Manual speaker setup on page 87. However, if SP: B ON is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed). All speaker systems (except 7. 1ch + Speaker B connections) are switched off when headphones are connected. 3 Use the INPUT SELECTOR dial to select the source for the zone you have selected. For example, ZONE 2 DVD sends the source connected to the DVD inputs to the primary (ZONE 2) sub room. If you select TUNER, you can use the tuner controls to select a preset station (see Saving station presets on page 41 if you're unsure how to do this). The tuner cannot be tuned to more than one station at a time. Therefore, changing the station in one zone also changes the station in the other zone. Please be careful not to change stations when recording a radio broadcast. Using the MULTI-ZONE controls The following steps use the front panel controls to adjust the sub zone volume and select sources. See MULTI-ZONE remote controls on page 62. 1 Press MULTI-ZONE ON/OFF on the front panel. Each press selects a MULTI-ZONE option: 4 When Speaker System is set to 7. 1ch + ZONE 2, use the MASTER VOLUME dial to adjust the volume for the sub zone. En 61 09 Using other functions 5 When you're finished, press MULTI-ZONE CONTROL again to return to the main zone controls. You can also press MULTI-ZONE ON/OFF on the front panel to switch off all output to the sub zone(s). You won't be able to switch the main zone off completely unless you've switched off the MULTI-ZONE control first. If you don't plan to use the MULTI-ZONE feature for a while, turn off the power in both the sub and main rooms so that this receiver is in standby. Button(s) MUTE <a> What it does Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound). 3 Select the input signal according to the signal to be recorded. Use the remote control's SIGNAL SEL button. % Set the remote control to the receiver operation mode, then press SLEEP repeatedly to set the sleep time. 30 min Off 60 min 90 min 4 Prepare the recorder. a You can only use this button when Speaker System is set to 7. 1ch + ZONE 2. Making an audio or a video recording You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV). Keep in mind you can't make a digital recording from an analog source or vice-versa, so make sure the components you are recording to/from are hooked up in the same way (see Connecting your equipment on page 14 for more on connections). The output switches among HDMI OUT ALL, HDMI OUT 1 and HDMI OUT 2 each time the button is pressed. 2 Prepare the source you want to record. Tune to the radio station, load the CD, video, DVD etc. 62 En Using other functions 09 !The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to HDMI OUT 1, then select the synchronized amp mode on the TV using the TV's remote control. 2 When you're finished, press STATUS again to switch off the display. Default system settings Setting Default ON FH/FW 9. 1ch FH/FW Front Center Speaker Setting FH/FW Surr SB SW Surround Position Crossover X-Curve DIMMER Inputs See Input function default and possible settings on page 36. HDMI HDMI Audio HDMI output Control Control Mode Display Power Off Audio playback Power On Level Volume Limit Mute Level Phase Control iPod/USB, HOME MEDIA GALLERY, ADAPTER PORT input function Other input functions LAST OFF FULL ON Amp HDMI OUT ALL ON ALL YES SMALL SMALL SMALL SMALL SMALLx2 YES IN REAR 80 Hz OFF Medium bright Digital Video Converter SPEAKERS Speaker System Setting Sound Delay Dual Mono DRC SACD Gain LFE Attenuate Auto delay Digital Safety Effect Level 2 PL II Music Options ExtendedStereo Other modes Center Width Dimension Panorama Default 0. 0 frame CH1 AUTO 0 dB 0 dB OFF OFF 90 50 3 0 OFF Neo:X CINEMA: 1. 0 Neo:X MUSIC: 0. 3 Neo:X GAME: 1. 0 MID AUTO SURROUND STEREO Resetting the system Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. Disconnect the iPod and USB memory device from the receiver beforehand. Set the Control with HDMI to OFF (see HDMI Setup on page 54). About the Speaker B Link function When 7. 1ch + Speaker B or 5. 1ch + SP-B Bi-Amp is selected for the Speaker System setting (page 87) and the Speaker B Link setting (HDMI Setup on page 54) is turned on, the setting of the played speaker terminals switches automatically when HDMI OUT is switched. HDMI OUT ALL ­ Switches to SP: A+B ON. Sound is output simultaneously in the room where the A speakers are located and in the room where the B speakers are located. Sound is only output in the room where the A speakers are located. Sound is only output in the room where the B speakers are located. 1 Switch the receiver into standby. 2 While holding down ENTER on the front panel, press u STANDBY/ON. The display shows RESET c NO d. 3 Select `RESET' using PRESET k/l, then press ENTER on the front panel. The display shows RESET? [. . . ] 1 Remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AAA size IEC R03 dry cell batteries . . . . . . . . . . . . . . . . . . . . 2 iPod cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Wireless LAN converter (AS-WL300) . . . . . . . . . . . . . . . . . [. . . ]