User manual PIONEER CT-F9191

[. . . ] However, the method of connecting and operating the unit is the same. IMPORTANT NOTICE [For U. S. model] The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This product complies with the Low Voltage Directive (73/23/EEC), EMC Directives (89/336/EEC, 92/31/EEC) and CE Marking Directive (93/68/EEC). IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] When it reaches the end of the reverse side, the tape stops automatically (auto stop function). If playback or recording is started from the reverse side, the tape will stop when it reaches the end of that side. Repeat mode position When the switch is set to this position for playback, both sides of the tape are played back repeatedly until the stop (7) button is pressed, or until the tape has been replayed 15 times (32 sides playback). If the pause button is pressed to pause the tape, and then playback is restarted, the repeat mode starts over from the beginning, and will play the tape 15 times (32 sides playback). When the switch is set to this position for recording, both sides are recorded and then the tape stops, as described above for the two way mode. RELAY PLAY/BLANK SKIP If Deck I and II are loaded with tapes, each tape will be played using relay palyback. DOLBY NR 7 Dolby NR System Dolby NR systems are designed to reduce the amount of tape hiss, mainly in the treble components. During recording, the highpitched pianissimo sounds which are most characteristic of audible noise are boosted, and during playback, only these boosted sections are attenuated, so that tape sound is returned to normal. As a result, the noise is attenuated by an amount equal to the boosting in the treble range. The Dolby B-type NR system reduces noise in the treble range, cutting tape hiss and expanding the dynamic range. The Dolby C-type NR system is even more effective in reducing noise, as it reduces noise from the mid-range on. NOTE: When a tape has been recorded using the Dolby B-type or C-type NR system, make sure that the DOLBY NR switch is set to the same position during playback. FUNCTION DISPLAY 1 23 4 DECK I REV PLAY FWD COPY REC DECK @II REV PLAY FWD LEFT LEVEL RIGHT -0 0 -15 -9 -3 Y0 -3 dB OPERATION OF DECK I WITH A REMOTE CONTROL UNIT NOT DESIGNED FOR DOUBLE DECKS (System remote control) Selecting DECK I In order to operate DECK I with the remote control unit, adjust the unit as follows: With the power off, press and hold the stop (7) button of DECK I, and turn the power on. Continue to hold the stop (7) button for approximately five seconds. ÷ Always set the switch to the same positions that was used for recording. Set the REV MODE switch to (See table entitled "PLAYBACK SEQUENCE WITH REV MODE SWITCH SETTING" on this page). Set the stereo amplifier for tape playback. Press the playback (3 or 2) button of the deck that will start to play first. ÷ When the tape in one deck ends, the other deck automatically begins playback. ÷ To cancel relay playback, press the stop (7) button. PLAYBACK SEQUENCE WITH REV MODE SWITCH SETTING The playback sequence depends on the setting of the REV MODE switch and on which playback (3 or 2) button is pressed first. The playback sequence for each possible selection is shown below. *2 In the repeat ( ) mode, relay playback always begins from the forward direction. I # : DECK I forward playback I @ : DECK I reverse playback II # : DECK II forward playback II @ : DECK II reverse playback : Auto-reverse function = : Relay REV Starting Other MODE playdeck switch back mode button DECK I3 Playback sequence *2 I# I @=II # II @=I # I @. . . 15 times relay (32 sides playback) NOTES: ÷ Relay playback can begin from either DECK I or DECK II. ÷ The tape in the idle deck can be replaced during relay playback mode, allowing many tapes to be played back continuously. [. . . ] DC servo motor x 2 Wow and Flutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 09% (WRMS) ±0. 19% (DIN) Fast Winding Time Approximately 100 seconds (C-60 tape) Frequency Response ­20 dB recording: TYPE IV (Metal) tape . . . . . . . . . . . . . . . . . . . . . . 20 to 16, 500 Hz TYPE II (High/CrO2) tape . . . . . . . . . . . . . . . . 20 to 16, 000 Hz TYPE I (Normal) tape . . . . . . . . . . . . . . . . . . . . . [. . . ]