User manual PIONEER CT-S66R

[. . . ] The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e. g. , 230 V D3-4-2-1-4_A_En or 120 V) written on the rear panel. WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the D3-4-2-1-7a_A_En equipment. If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. [. . . ] · FRONT ALIGN ­ Speakers are set in accordance with the front speaker settings. The sound of the test tone will alternate between the left front (reference) speaker and the target speaker. 3 Select the channel(s) you want and adjust to your liking. 3e. EQ CUSTOM1 Adjust Test Tone Type: "ALL CH ADJUST" Left 40Hz : [+ 1. 0dB ] 125Hz : [ 0. 0dB ] 250Hz : [ 0. 0dB ] 4kHz : [ 0. 0dB ] 13kHz : [ 0. 0dB ] TRIM : [ 0. 0dB ] :Finish 3e. EQ CUSTOM1 Adjust Test Tone Type: "ALL CH ADJUST" [ Left ] 40Hz : + 1. 0dB 125Hz : [ 0. 0dB ] 250Hz : [ 0. 0dB ] 4kHz : [ 0. 0dB ] 13kHz : [ 0. 0dB ] TRIM : [ 0. 0dB ] :Finish 2 Select CUSTOM1 or CUSTOM2 then use select the setting you want to copy. 3d. EQ Data Copy TO CUSTOM1 CUSTOM2 Start Copy [ FROM CUSTOM1 CUSTOM2 [ OK ] ] 3d. EQ Data Copy TO CUSTOM1 CUSTOM2 Start Copy [ FROM ALL CH ADJ CUSTOM2 ] [ OK ] / to Use / to select the channel. Use / to select the frequency and / to boost or cut the EQ. When you're finished, go back to the top of the screen and use / to select the next channel. · The front speakers can't be adjusted if you selected FRONT ALIGN. indicator shows in the display if the frequency adjustment is too drastic and might distort. If this happens, bring the level down until OVER!disappears from the display. :Cancel :Cancel · You can also copy from one custom setting to another. For more on the ALL CH ADJUST and FRONT ALIGN settings, see Setting the Acoustic Calibration EQ automatically above. 3 Select `OK' to copy and confirm. 39 En 08 The System Setup menu Tip · Changing the frequency curve of one channel too drastically will affect the overall balance. Also, the center, surround, and surround back speakers can't be set to LARGE if the front speakers are set to SMALL. In this case, all bass frequencies are sent to the subwoofer. 40 En The System Setup menu 08 · Center ­ Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn't connect a center speaker, choose NO (the center channel is sent to the other speakers). · Surr ­ Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn't connect surround speakers choose NO (the sound of the surround channels is sent to the other speakers). · SB ­ Select the number of surround back speakers you have (one, two or none). Select LARGE if your surround back speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn't connect surround back speakers choose NO. 1 · SUB W. ­ LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES is selected (see notes below). [. . . ] . 5 Hz to 10 MHz Component Video Section Input (Sensitivity/Impedance) . . 5 Hz to 100 MHz FM Tuner Section Frequency Range . 87. 5 MHz to 108 MHz Usable Sensitivity . Mono: 13. 2 dBf, IHF (1. 3 µV/75 ) 69 En 13 Additional information Cleaning the unit · Use a polishing cloth or dry cloth to wipe off dust and dirt. [. . . ]