User manual PIONEER DJM-3000

[. . . ] Operating environment temperature and humidity: +5°C ­ +35°C (+41°F ­ +95°F); less than 85%RH (cooling vents not blocked) Do not install in the following locations ÷ Location exposed to direct sunlight or strong artificial light ÷ VENTILATION: When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 3 cm at each side). wARNING: Slot and openings in the cabinet are provided for Ventilation and to ensure reliable operation of the product and to protect it from overheating, to prevent fire hazard, the openings should never be blocked and covered with items, such as newspapers, table-cloths, curtains, etc. Also do not put the apparatus on the thick carpet, bed, sofa, or fabric having a thick pile. Changing between three kinds of effect mix (ECHO, ZIP, ROLL) can be performed easily merely by operating the Cross fader lever, or by pressing the Effect select/start switch. [. . . ] Mixing with original sound produces a choral effect. Effect DELAY Effect Parameter 1 (TIME) Delay time Setting range: 1 to 3500mSec, in 1msec steps Delay time Setting range: 1 to 3500mSec, in 1msec steps Pan time (changeover time) Setting range: 10 to 16000mSec, in 5mSec steps for 10 to 1000 and 10msec steps for 1000 to 16000 Trans time (changeover time) Setting range: 10 to 16000mSec, in 5mSec steps for 10 to 1000 and 10msec steps for 1000 to 16000 Filter time (cycle) Setting range: 10 to 16000mSec, in 5mSec steps for 10 to 1000 and 10msec steps for 1000 to 16000 Flanger time (cycle) Setting range: 10 to 16000mSec, in 5mSec steps for 10 to 1000 and 10msec steps for 1000 to 16000 Effect Parameter 2 (LEVEL/DEPTH) Effect mix ratio (Balance between original and delayed sound levels) Effect mix ratio (Balance between original and echo sound levels) Effect mix ratio (Balance between original and panned sound levels) Effect mix ratio (Balance between original and cut sound levels) * The BPM band that matches the music on CH-2 can be selected with the BPM counter range selector switch. * The counter will flash if BPM cannot be counted for more than 2 seconds. In this case, use manual mode to make settings (see pages 26-27). P CUE switch (in the BEAT EFFECTS controls) is pressed, the effect can be confirmed by listening to the headphones output. setting the Delay Time ÷ Setting the delay time to match one beat of the BPM displayed on the AUTO BPM COUNTER makes effect application more effective. By pressing the Effect beat selector switch (@ or #), delay time of 1/4 to 8/1 can be set for one beat of the counted BPM. More precise delay times can be set with the Effect PARAMETER 1 control (TIME). As "1/2" will light on the beat display if delay time is set to 1/2 of one beat of the BPM, the parameter value can be set using the beat display as a guide. setting to Balance Original and Delayed Sound Levels ÷ The balance between original and delayed sound levels is set using the Effect PARAMETER 2 control (LEVEL/ DEPTH). Turning this control to the left will decrease delayed sound and turning it to the right will increase it. If the switch is pressed once more, the effect will be turned off. * If it is turned on in time to the beat, the effect's cycle will also start on the beat. SELECT switch when delay, echo, reverb (pages 22-23) and similar effects have been turned on, all of the reverberation of the prior channel's effects will be output. Only operate the Effect selector switch when effects are off (when the Effect ON/OFF switch is lit orange). Operating it with effects on could generate noise. Display where a 1/2-beat delay (250mSec) has been set to music with a BPM of 120 (time conversion: 500mSec). Effect REVERB Effect Parameter 1 (TIME) Reverb time (echo time) Setting range: 1 to 100%, in 1% steps Pitch Setting range: 0 to ±100%, in 1% steps Effect Parameter 2 (LEVEL/DEPTH) Effect mix ratio (Balance between original and reverb sound levels) Effect mix ratio (Balance between original and pitch-shifted sound levels) * The entire BPM display will turn off. P CUE switch (in the BEAT EFFECTS controls) is pressed, the effect can be confirmed by listening to the headphones output. setting Pitch ÷ Pressing # on the Effect beat selector switch will increase the pitch setting +33%, +50% or +100%, while pressing @ will decrease it ­33%, ­50% or ­100%. More precise pitch can be set with the Effect PARAMETER 1 control (TIME). setting the Balance Between Original and PitchShifted Sound Levels ÷ The balance between original and pitch-shifted sound levels is set using the Effect PARAMETER 2 control (LEVEL/DEPTH). [. . . ] ¶ If the Effect select/start switch is pressed during output of the B side sound, the selected effect will be applied to B, and after the preset effect time has elapsed, sound A will be output. [Operation if Cross fader lever is midway when the Effect Mix Auto mode is turned on] ¶ If the Effect select/start switch is pressed when both A and B sounds are being output, the selected effect will be applied to B, and after the preset effect time has elapsed, sound A will be output. ¶ If the Cross fader lever is moved toward either side A or B when both A and B sounds are being output, the ordinary cross fader operation will occur. ¶ Two or more effects cannot be selected at the same time. [. . . ]