User manual PIONEER DVR-310

[. . . ] DVD Recorder DVR-310 4. 7 Operating Instructions Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference. In some countries or regions, the shape of the power plug and power outlet may differ from that shown in the explanatory drawings. [. . . ] See Setting the picture quality/recording time on page 44 for detailed information. 3 Check that the `Audio In' settings for `External Audio' and `Bilingual Recording' are as you want them. See Audio In settings on page 79 for more on these settings. · Use REC MODE to set the recording quality. See Setting the picture quality/recording time on page 44 for detailed information. 5 Press and hold the FUNCTION button on the front panel for 3 seconds. The recorder goes into standby and the AUTO indicator in the front panel display lights. 51 En 06 Recording The recorder will automatically switch on and start recording when the other component comes on. Recording stops when the external component switches off. · To cancel Auto Start Recording, press ON. STANDBY/ Recording from a DV camcorder VR mode Video mode · To cancel Auto Start Recording once recording has already started, press ì REC for 3 seconds, then STOP REC. Note · You can't set Auto Start Recording when: · the recorder is recording or in timer recording standby. · there is no recordable disc loaded. · the disc loaded already contains the maximum number of titles (99). · If Auto Start Recording is set, it will not start if another timer recording is in progress. · Timer recordings take precedence over Auto Start Recording. Auto Start Recording will stop if a timer recording is due to start. After the timer recording has finished, Auto Start Recording will resume. You can record from a DV camcorder connected to the DV IN/OUT jack on the front panel of this recorder. Using the recorder's remote, you can control both the camcorder and this recorder. Before recording, make sure that the audio input for the DV IN/OUT jack is setup (see DV Input on page 79). CLEAR ENTER HOME MENU RETURN REV SCAN PLAY FWD SCAN PAUSE STOP STEP/SLOW REC MODE ì Important · The source signal must be DVC-SD format · Some camcorders cannot be controlled using this recorder's remote. · If you connect a second recorder using a DV cable, you cannot control the second unit from this one. · You can't control this unit remotely from a component connected to the DV IN/OUT jack. · You can't record date and time information from DV cassette. · You can't record copy-protected or copy-once material. · During DV recording, if a part of the tape is blank, or has copy-protected material on it, this recorder will pause recording. [. . . ] 1­6 hours Receivable channels PAL B/G VHF (low) VHF (high) Frequency 47 - 89 MHz 104 - 300 MHz Channel E2 - E4 X-Z E5 - E12 S1 - S20 M1 - M10 U1 - U10 S21 - S41 E21 - E69 PAL I Frequency 44 - 89 MHz 104 - 300 MHz Channel A-C X-Z D-J 11, 13 S1 - S20 S21 - S41 E21 - E69 Hyper UHF 302 - 470 MHz 470 - 862 MHz 302 - 470 MHz 470 - 862 MHz SECAM D/K VHF (low) VHF (high) Frequency 49 - 94 MHz 104 - 300 MHz Channel R1 - R5 R6 - R12 S1 - S20 NTSC M/N Frequency 54 - 130 MHz 130 - 364 MHz Channel 2 - 6 (AIR) 2 - B (CATV) 7 - 13 (AIR) C - W+11 (CATV) Hyper UHF 302 - 470 MHz 470 - 862 MHz S21 - S41 E21 - E69 Not applicable 365 - 803 MHz 14 - 69 (AIR) W+12 - W+84 (CATV) STEREO B/G - A2 I - NICAM B/G - NICAM D/K - NICAM M/N - BTSC Timer Programs . Quartz lock (24-hour digital display) Power off memory . 5 years (after manufacture) Input/Output VHF/UHF antenna input/output terminal . VHF/UHF set 75 (F-shape connector) Video input . [. . . ]