User manual PIONEER F-F6-J

[. . . ] RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain D3-4-2-1-3_A_En or moisture. When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 10 cm at top, 10 cm at rear, and 10 cm at each side). Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. [. . . ] 5 seconds or more to perform rapid tuning. If the TUNED or STEREO indicator fails to light when tuning into an FM station due to a weak reception signal, press the MPX button to switch the tuner into mono reception mode. 1 This should improve the sound quality and allow you to enjoy the broadcast. Steps 1 to 5 can be skipped when using the ST +/­, preset channel range (A to J) and station call (1 to 10) buttons. The preset mode is set when any of these buttons is pressed, regardless of the menu setting at that time. 4 Either turn the TUNING/PRESET dial or press the ST + or ST ­ button to select the search mode. 1 The STEREO indicator will light blue when the MPX button is pressed. 5 While the preset channel number is flashing, press one of the preset channel range (A to J) buttons to select the desired memory block (A to J). 6 While the preset channel number is flashing, either turn the TUNING/PRESET dial, press the ST +/­ or Station call (1 to 10) button to select the desired preset channel (1 to 10). 1 7 While the preset channel number is flashing, either press the TUNING/PRESET dial or the MEMORY button to store the station in the preset memory. ⷠTo preset other channels, repeat steps 2 to 6. ⷠA total of 100 broadcast stations can be preset -- 10 stations (channels 1 to 10) in each of blocks A to J. 4 Press the TUNING/PRESET dial or ENTER button to set the preset mode and make the preset channel number flash. ⷠSteps 1 to 4 can be skipped when using the MEMORY button. When this button is pressed, the preset memory standby mode is set, regardless of the menu setting at that time. 1 When the preset channel is A1, pressing the ST ­ button or rotating the TUNING/PRESET dial to the left will cause the preset channel to move to J10. Radio Data System (RDS) is a system used by most FM radio stations to provide listeners with various kinds of information, such as the name of the station and the kind of show being broadcast. One feature of RDS is that you can search by type of program. For example, you can search for a station that's broadcasting a show with the program type, JAZZ. You can search the following program types:1 POP M ­ Pop music ROCK M ­ Rock music EASY M ­ Easy listening LIGHT M ­ `Light' classical music CLASSICS ­ `Serious' classical music OTHER M ­ Music not fitting above categories WEATHER ­ Weather reports FINANCE ­ Stock market reports, commerce, trading, etc. CHILDREN ­ Programs for children SOCIAL ­ Social affairs RELIGION ­ Programs concerning religion PHONE IN ­ Public expressing their views by phone TRAVEL ­ Holiday-type travel information as opposed to traffic announcements. LEISURE ­ Leisure interests and hobbies JAZZ ­ Jazz COUNTRY ­ Country music NATION M ­ Popular music in a language other than English OLDIES ­ Popular music from the '50s and '60s FOLK M ­ Folk music DOCUMENT ­ Documentary You can search for any of the program types listed above. [. . . ] If the trouble cannot be rectified even after performing the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. ⷠIf the unit does not operate normally due to external effects such as static electricity, disconnect the power plug from the outlet and insert again to return to normal operating conditions. remedy · Disconnect the power plug from the outlet, and insert again. ⷠIf you're trying to switch on using the remote control, make sure the front panel POWER button is switched on first. [. . . ]