User manual PIONEER GM-A5602

[. . . ] English Owner’s Manual Mode d’emploi BRIDGEABLE TWO-CHANNEL POWER AMPLIFIER AMPLIFICATEUR DE PUISSANCE PONTABLE À DEUX CANAUX AMPLIFICATORE DI POTENZA A DUE CANALI COLLEGABILE A PONTE AMPLIFICADOR DE POTENCIA DE DOS CANALES PUENTEABLE BRÜCKBARER ZWEI-KANAL-LEISTUNGSVERSTÄRKER SCHAKELBARE 2-KANAALSVERSTERKER ДВУХКАНАЛЬНЫЙ УСИЛИТЕЛЬ МОЩНОСТИ С ВОЗМОЖНОСТЬЮ МОСТОВОГО ВКЛЮЧЕНИЯ Français Italiano Español GM-A5602 GM-A3602 Deutsch Nederlands Русский Section 01 Before you start Thank you for purchasing this PIONEER product To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the manual in a safe and accessible place for future reference. We offer the latest information about PIONEER CORPORATION on our website. [. . . ] If you hear too much noise when using the speaker input terminals, turn the gain control to higher level. 5 Power indicator The power indicator lights up to indicate power ON. Rear side GM-A3602 Front side Rear side To adjust the switch, use a flathead screwdriver if needed. 1 LPF (low-pass filter) switch Switch the settings based on the connected speaker. This eliminates high range frequency and outputs low range frequency. Protective function included to prevent malfunction of the unit and/or speakers due to excessive output, improper use or improper connection. , this function cuts off the output for a few seconds as a normal function, but output is restored when the volume of the head unit is turned down. 4 En Section Setting the unit !A cut in sound output may indicate improper setting of the gain control. To ensure continuous sound output with the head unit at a high volume, set amplifier gain control to a level appropriate for the preout maximum output level of the head unit, so that volume can remain unchanged and to control excess output. Despite correct volume and gain settings, the unit sound still cuts out periodically. in such cases , please contact the nearest authorized Pioneer Service Station. Gain control of this unit Preout level: 2 V (Standard: 500 mV) Preout level: 4 V 02 English If the signal waveform is distorted due to high output, even if the amplifier gain is raised, the output power will change only slightly. Above illustration shows NORMAL gain setting. Relationship between amplifier gain and head unit output power If amplifier gain is raised improperly, this will simply increase distortion, with little increase in power. Signal waveform when outputting at high volume using amplifier gain control En 5 Section 03 Connecting the units Connection diagram The female terminal can be connected to the auto-antenna relay control terminal. If the car stereo lacks a system remote control terminal, connect the male terminal to the power terminal via the ignition switch. Speaker output terminals Please see the following section for speaker connection instructions. Refer to Connections when using the speaker input wire on page 8. Fuse 30 A × 2 (GM-A5602) / 25 A × 1 (GMA3602) Fuse (30 A) × 2 Grommet Rear side Front side 9 a b c d e Before connecting the amplifier WARNING 1 Special red battery wire RD-223 (sold separately) After completing all other amplifier connections, finally connect the battery wire terminal of the amplifier to the positive + battery terminal. 2 Ground wire (Black) RD-223 (sold separately) Connect to metal body or chassis. 3 Car stereo with RCA output jacks (sold separately) 4 External output 5 Connecting wire with RCA pin plugs (sold separately) 6 Speaker input terminal (use a connector included) Please see the following section for speaker connection instructions. [. . . ] Connections when using the speaker input wire Connect the car stereo speaker output wires to the amplifier using the supplied speaker input wire. Do not connect both the RCA input and the speaker input at the same time. WARNING If the battery wire is not securely fixed to the terminal using the terminal screws, there is a risk of overheating, malfunction and injury, including minor burns. 1 Route battery wire from engine compartment to the vehicle interior. [. . . ]