User manual PIONEER PDA-5001

[. . . ] · We guarantee the performance of our products only when they are assembled and adjusted in accordance with this installation manual. · The specifications and external designs shown in this installation manual are subject to change without notice. CAUTION Exclamation marks placed within triangles are intended to alert users to the presence of important safety information. Be sure to read instructions indicated by this symbol. Contents 1. Product Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Rapid temperature fluctuations can deposit water vapor inside the unit, degrading performance. If condensation occurs, turn the unit off and leave it off for an hour or so. It is also good practice to increase the room temperature gradually. 7-3 Repeater box anchoring method · To anchor the repeater box by hanging it on a wall for example, use the anchor holes in the tabs on both sides of the box (see 6. · When installing it behind the plasma display, install it below the center line of the plasma display in order to prevent the exhausted air from raising the temperature. Lower side · Because the direction that the repeater box is installed is not specified, install it in a direction suited to the wiring. ­ But be certain that it is not enclosed by anything that will block the discharge of heat. 7-4 Other installation conditions The unit is designed for indoor use, and is not suited for open-air use. Make the total rising/descending vertical distance 7 m (22. 96 ft) or less, and the vertical height difference 3 m (9. 84 ft) or less. Examples: Rising distance Case A Case B 4 m (13. 12 ft) 4 m (13. 12 ft) Total rising/descending distance 7 m (22. 96 ft) or less Descending distance Total distance 3 m (9. 84 ft) 0 m (0 ft) 7 m (22. 96 ft) 4 m (13. 12 ft) Judgement Vertical height difference 3 m (9. 84 ft) or less Height difference 1 m (3. 28 ft) 4 m (13. 12 ft) X X Judgement Overall judgement 3m (9. 84 ft) 4m (13. 12 ft) Ceiling 4m (13. 12 ft) A Floor B ­ If criteria 1 and 2 cannot be satisfied, cut the CD tube midway and pass the cables through them separately. 8-3 Passing cables through the CD tube When a pull-through line has already been inserted in the CD tube, attach the cables to the pull-through line and pull them through the CD tube. Make sure the connection has as few protrusions as possible so that it will not break during the pass through work. If a pull-through line has not been inserted in the CD tube, pull it through with mechanics wire etc. . with total length of 30 m (98. 43 ft) to pull it through. There are cases where, as the cable is passed through, it produces high friction with the CD tube so it cannot be passed through. · When removing the Optical Connector from the Transmitter/Receiver Box, do not pull the Cable but, rather, pull the Connector straight out while squeezing the clips on either side of the connector. 1 Do not remove the dustproof cap from the Optical Cable/Repeater Box until immediately before connecting the cable. Repeater box Optical cable 2 When connecting the Optical Cable to the Repeater Box, always push the connector home while squeezing the clips on either side of the connector. When connecting, be sure to hold the connector, squeezing the clips (marked with an arrow). Do not remove the dustproof cap until immediately before connection. Optical receptacle Step 9-3 Optical cable Align the connector with the slot in the receptacle. The foolproof protrusion goes to the bottom. Step 9-3 Figure 5 ­ Connection of Optical Cable to Repeater Box If subjected to physical shock or force, the optical cable may bend or break, thus preventing it from transmitting signals. When anchoring it, do not use any tools that would exert undue force such as staplers; always fix the cable gently but firmly, for example with a cable clamp, as illustrated on the right. Place a dustproof cap on any unconnected Optical Connector. Any foreign particles adhering to or within either Optical Connector parts or the Optical Receptacle may prevent normal operation. Do not bend the optical cable through a radius of less than 15 mm. Thoroughly check the direction of the foolproof protrusion prior to connection. This optical cable product is designed for indoor use. Do not use it outdoors. Never look directly into the Optical Receptacle or at the tip of the Optical Connector while the power to the Transmitter Box is ON. If the laser beam runs into your eyes, it may cause you visual impairment. CAUTION 14 9. [. . . ] * The transmitter and receiver of the repeater box are referred to as the "transmitter" and "receiver" below. * Shaded areas ( ) indicate that service from Pioneer is required. Connect the AC adapter. Yes If the problem is not resolved after rechecking the connections etc. , please contact PIONEER'S SERVICE. Yes Are all LED other than the PWR of the transmitter and receiver lit?Yes Is the PDA-5001 changed to the standard cable and operating normally?Yes If the problem is not resolved after rechecking the connections etc. , please contact PIONEER'S SERVICE. No Please see "When there is no picture and sound". No If the problem is not resolved after rechecking the connections etc. , please contact PIONEER'S SERVICE. 19 10. [. . . ]