User manual PIONEER PDA-H05

[. . . ] Optical System Cable (PDA-H05) Installation Manual (Ver. 1. 0) This manual provides precautions and information for installation, preparation, and handling of the optical system cable. Before installation and preparatory work, choose a safe and appropriate site after thorough consideration of construction, materials used, strength, and surroundings. If adequate safeguards are not in place, immediately halt the installation process and discontinue marketing activities. PRECAUTIONS: · We accept no responsibility for losses resulting from the use of parts other than those supplied by us. [. . . ] with total length of 30 m (98. 43 ft) to pull it through. There are cases where, as the cable is passed through, it produces high friction with the CD tube so it cannot be passed through. In such cases apply pass-through grease or powder to the cables so that they will pass through smoothly. We recommend that you prepare pass-through grease before passing the cables through the CD tube. But it will not move 30 m (98. 43 ft) even if grease is used. In such cases cut the CD tube midway and pass the cables through one CD tube then through the other CD tube. Pass-through grease 9 8. When Passing the Cables Thorough the CD Tube 8-4 Method of combining cables before the pass-through step Step 1 Optical cable Wrap the connector in a sheet. Sheet that was wrapped around the repeater box (cut to the suitable size). Held in place gently with cellophane tape. Step 2 Overlap the optical cable and the pull-through line. Knot (do not let it become undone) Pull-through line Optical cable Step 3 Combine the optical cable and the pull-through line with adhesive tape being careful that the knot does not become untied. The strength is applied in this part when it is pulled. Adhesive tape Slightly separated from the connector. Step 4 Anchor the connector with adhesive tape coated with pass-through grease to protect it so that it is not exposed and does not catch on the tube. Adhesive tape As short as possible. (If it is long, resistance is produced when it is passed through a bent CD tube. ) Notes: · When pulling the optical cable, do not pull only the connector. · Be sure to never combine the pull-through line so that it applies direct force on the connector, because this may pull out the connector. · The force used to pull the optical cable must be no greater than 40N (Newton). If it is pulled with force greater than 40N (Newton), the properties of the optical cable will deteriorate. 10 9. Optical System Cable Connection Procedure Important: Please use the installation procedure below. Make sure that the AC power plugs of Plasma Display and Media Receiver should not be connected to the AC power receptacles. Note: Be careful not to uncover the dust rubber plugs to the Transmitter and Receiver Boxes and the dust caps for the optical cables until installing the optical system cable. Ensure to keep those dust plugs plugged securely whenever disconnecting the system. 9-1 Connecting the Media Receiver Connection of Transmitter Box and Media Receiver via System Connector (White). Notes: · Be careful not to fix cables too tightly when tacking them to walls or to bend them excessively. · Be careful of the System Cable connector (white). Make sure not to bend or distort the metal connector which would prevent it from making a proper connection. Media receiver Media Receiver terminal (white) for System Cable connection Step 9-1 System cable (Connector: White) "TRANSMITTER" should be marked here. Figure 1 ­ Connection of Transmitter Box and Media Receiver via System Connector (White) 11 9. Optical System Cable Connection Procedure 9-2 Connecting the Plasma Display Connect the System Cable (connector: white) of the Receiver to the Display following the same sequence of steps as in Step 9-1. Note: Be careful of the System Cable connector (white). Make sure not to bend or distort the metal connector which would prevent it from making a proper connection. Step 9-2 "RECEIVER" should be marked here. Display terminal (white) for System Cable connection System cable (Connector: White) Figure 2 ­ Connection of Receiver Box and Display via System Connector (White) And connect one end of the System Cable (connector: silver) to the System Connector (silver) of the Transmitter Box and the other end to the Receiver Box as shown in Figure 3. Transmitter box System cable (connector: silver) Figure 3 ­ Connection of System Cable (Connector: Silver) 12 9. Optical System Cable Connection Procedure Connect the system cable (Connector: black) as shown in Figure 4. Display Media receiver Transmitter box Receiver box Media Receiver terminal (black) for System Cable connection System cable (Connector: Black) Display terminal (black) for System Cable connection System cable (Connector: black) Figure 4 ­ Connection of the System Cable (Connector: Black) 13 9. Optical System Cable Connection Procedure 9-3 Connection of Optical cable Remove the dustproof cap from Transmitter/Receiver Box. Aligning the foolproof protrusion, push the Optical Connector home into the Optical Receptacle until it "clicks. " Cautions · Do not remove the dustproof cap from the Transmitter or Receiver Box or from Optical Cable until the Optical Cable has been connected. [. . . ] Troubleshooting When the unit does not operate properly even after connection There is a possibility that the connectors are dirty. Please reconnect after performing the following procedure. Cleaning the sides of the optical cable end (ferrule) A cleaner should be used only once. Cleaner part Cleaner for the sides of the ferrule end. Cover the ferrule with the cleaner and turn five times. 2. [. . . ]