User manual PIONEER PDK-TS03

[. . . ] This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage. ¶ Consult your dealer if you encounter any difficulties with this installation. ¶ Pioneer is not liable for any damage resulting from improper installation, improper use, modification, or natural disasters. Do not use this stand for a plasma display or any other purpose that is not specified. [. . . ] Install this product so that during routine use or when rotated, it does not protrude from where the rack or the like has been installed. Failure to do so could cause unforeseen accidents, such as the equipment breaking or falling over. 15) In addition, be careful not to insert your hand at the base of the resin cover, as doing so could cause injury. Prevent accidents by taking thorough measures to ensure that the equipment does not fall over. Place a sheet or protective cover to protect the display from scratches or damage. Assemble only with the plasma display lying flat on a table or similar surface. Insert the bolts vertically in the holes and tighten them, but do not apply excessive pressure that tightens them more than necessary. Move the stand so that the stand screw holes and the nuts that connect the main display line up correctly. The display is a 50" model that weighs approximately 40 kilograms (88 lb) and has little depth, making the display very unstable. For this reason, at least two people are required for setup and installation. With the plasma display lying flat, insert and secure the two Installation bolts 1 (M8 x 20) in the holes "a" located in the plasma display housing. At this point, tighten these bolts 1 only until the threads are no longer visible when viewed from t he side (you will be unable to attach the display if the bolts are screwed in completely). Stop screwing down the bolt when the threads are no longer visible. ¶ Regarding the stand pipe screw holes when the stand is used as a desktop stand Table: Stand pipe screw holes when the stand is used as a desktop stand Plasma display model Specifications Without optional speakers Screw holes used with stand orientation With optional speakers attached to both sides of display Without optional speakers With optional speakers attached to both sides of display With optional speakers attached at bottom of display (They are used for separately sold options. As shown in figure, hook the stand pipe holes (either pipe A or B) onto the screw heads of the installation bolts 1, then slide the stand upwards to the main plasma display until it engages the installation bolts 1 (once put together with the display, the stand will slides no more than 19 mm (3/4 inch)). Pass the installation bolts 2 (M8 x 40) through the stand pipes and tighten the installation bolts securely with the included hexagonal wrench (The holes shpuld be used in the proper combinations, A­A' and B­B'). Using the hexagonal wrench provided, tighten the installation bolts 1 that were inserted in Step 1. After installing the stand, remove the rotation-preventing bolts from the holes for preventing the equipment from falling over. These bolts are to prevent deviations in rotation from occurring during transport. The stand could break if it is rotated excessively with the bolts still in place. [. . . ] Without speakers for the 50" display model With speakers for the 50" display model installed Without speakers for the 43" display model With speakers for the 43" display model installed 43" with optional speakers attached at bottom of display Emplacement de l'installation (a) Assurez-vous d'installer le support dans un endroit qui peut largement supporter le poids combiné du support et de l'affichage. ¶ Vision des trous de vis du pilier du support quand ce dernier est utilisé comme support de surface de table. Table: Les trous de vis du pilier de support quand ce dernier est utilisé comme support de surface de table Modèle d'écran plasma Spécificités Sans haut-parleurs optionnels Comme représenté sur la figure, accrochez les trous de piliers du support (tube A ou bien B) sur les têtes de vis des boulons d'installation 1. Puis glissez le support vers le haut à l'affichage de plasma principal jusqu'à ce qu'il engeance les boulons d'installation 1 (une fois assemblé avec l'affichage, le support ne glissera pas plus de 19 mm). [. . . ]