User manual PIONEER PDM-406A REV A1

[. . . ] Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer. [. . . ] Use / to adjust the volume of the speaker you selected to match the reference speaker. 38 En The System Setup menu 06 When it sounds like both tones are the same volume, press ENTER to confirm and continue to the next channel. 2a. Fine Channel Level L R C LS RS SW +0. 0dB [ 0. 0dB +1. 0dB [ ­3. 0dB [ +10. 0dB [ ­1. 5dB (Reference) ] ] ] ] 2 Adjust the distance of the left channel from the listening position. 2b. Fine SP Distance English L(Reference) 3. 0 m Deutsch ENTER:Next :Finish :Cancel · For comparison purposes, the reference speaker will change depending on which speaker you select. · If you want to go back and adjust a channel, simply use / to select it. 3 When you're finished, press RETURN. You return to the Manual MCACC setup menu. After pressing ENTER, test tones will be output. 3 Select each channel in turn and adjust the distance as necessary. Use / to adjust the delay of the speaker you selected to match the reference speaker. The delay is measured in terms of speaker distance from 0. 1 m to 9. 0 m. 2b. Fine SP Distance L R C LS RS SW 3. 0 [ 1. 8 3. 0 [ 1. 3 [ 1. 2 [ 2. 4 m (Reference) m] m m] m] m] Français Italiano Fine Speaker Distance · Default setting: 3. 0 m (all channels) For proper sound depth and separation with your system, it is necessary to add a slight bit of delay to some speakers so that all sounds will arrive at the listening position at the same time. The following setting can help you make detailed adjustments that you may not achieve using the Manual speaker setup on page 42. 1 Select `Fine SP Distance' from the Manual MCACC setup menu. The volume increases to the reference level. 2. Manual MCACC a. Fine Ch Level b. Fine SP Distance c. EQ AUTO Setting d. EQ Data Copy e. EQ CUSTOM1 Adjust f . EQ CUSTOM2 Adjust g. EQ Data Check :Return :Finish Nederlands Español Listen to the reference speaker and use it to measure the target channel. From the listening position, face the two speakers with your arms outstretched pointing at each speaker. For more on the ALL CH ADJUST and FRONT ALIGN settings, see Setting the Acoustic Calibration EQ automatically on page 40. 3 Select `OK' to copy and confirm. Français Setting the Acoustic Calibration EQ manually Before manually adjusting the Acoustic Calibration EQ, we recommend copying the ALL CH ADJUST or the FRONT ALIGN settings from the auto setup above (or from Automatically setting up for surround sound (MCACC) on page 8) to one of the custom settings. Instead of just a flat EQ curve, this will give you a reference point from which to start (see Copying your Acoustic Calibration EQ settings on page 40 for how to do this). 1 Select `EQ CUSTOM1 Adjust' or `EQ CUSTOM2 Adjust' from the Manual MCACC setup menu. 2. Manual MCACC a. Fine Ch Level b. Fine SP Distance c. EQ AUTO Setting d. EQ Data Copy e. EQ CUSTOM1 Adjust f . EQ CUSTOM2 Adjust g. EQ Data Check :Return 2e. EQ CUSTOM1 Adjust Test Tone Type ALL CH ADJUST Italiano Use / to select the channel. Use / to select the frequency and / to boost or cut the EQ. When you're finished, go back to the top of the screen and use / to select the next channel. · The front speakers can't be adjusted if you selected FRONT ALIGN. · The OVER indicator shows in the display if the frequency adjustment is too drastic and might distort. If this happens, bring the level down until OVER disappears from the display. Tip · Changing the frequency curve of one channel too drastically will affect the overall balance. If the speaker balance seems uneven, you can raise or lower channel levels using test tones with the TRIM feature. Use / to select TRIM then use / to raise or lower the channel level for the current speaker. [. . . ] 1 Vp-p/75 71 En 12 Additional information · Frequency response Miscellaneous Power requirements . AC 220 V to 230 V, 50 Hz/60 Hz Power consumption . 420 mm (W) x 158 mm (H) x 352. 5 mm (D) Weight (without package). 8. 1 kg DVR/VCR, DVD/BD, TV/SAT MONITOR . [. . . ]