User manual PIONEER PRO-1000HD

[. . . ] PLASMA DISPLAY PRO-1000HD PRO-800HD Operating Instructions Safety Precautions The following symbols are found on labels attached to the product. They alert the operators and service personnel of this equipment to any potentially dangerous conditions. IMPORTANT NOTICE The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCESSIBLE. WARNING This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage. CAUTION: CAUTION This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death. i ii PRO-1000HD / PRO-800HD Safety Precautions IMPORTANT SAFETY INSTRUCTIONS READ INSTRUCTIONS -- All the safety and operating instructions should be read before the product is operated. [. . . ] Input changes each time the main unit's INPUT is pressed as follows. 3 INPUT1 INPUT4 2 3 INPUT2 INPUT3 2 Before you begin, make sure you have: · Made connections between this unit and AV components or personal computer as described in the section "Installation and Connections" starting on page 8. · Set up the on-screen menu to input signals from components connected to INPUT1 and INPUT2 as described in the section "Setting Up the System" on page 18. If no connections are made to these terminals, on-screen setup is not necessary. · When the menu screen is displayed, changing the signal input will cause the menu screen to turn off. · If the input computer signal is not supported by the display, the following message will be displayed: I NPUT 1 CA U T I O N U N S UP P O R T E D S I G N AL fH: fV: 7 7. 0 H z 1 15 2X 864 FUL L 2, 5 I NPUT 1 2, 5 3 S-VIDEO VIDEO 3 CA U T I O N OU T OF R A N G E f H : 7 5. 0 H z ­­­­ FUL L 4 4 Main Unit Operating Panel Remote Control Unit Use VOLUME +/­ on the remote control unit to adjust the volume. If no audio connections are made to this unit, this step is not necessary. When viewing is finished, press STANDBY/ON to put the unit in standby mode. The STANDBY/ON indicator will blink and then remain lit (red) indicating that the standby mode is engaged. Operation is not possible while the STANDBY/ON indicator is blinking (red). Switch MAIN POWER on the main unit to the off position to turn the main power off. The STANDBY/ON indicator may continue to light for a short while even after the main power is turned off. This is a result of residual electric load impressed on the circuitry, and the light will turn off presently. 5 1 Switch the main power switch on the main unit to the on position to turn the main power on. Press STANDBY/ON to put this unit in the operation mode. The STANDBY/ON indicator turns green. 6 2 CAUTION Please do not leave the same picture displayed on the screen for a long time. Doing so may cause a phenomenon known as "screen burn" which leaves a ghost, or residual, image of the picture on the screen. 20 PRO-1000HD / PRO-800HD Operations To adjust the volume To confirm display settings DISPLAY S-VIDEO VIDEO VOLUME +/­ Press VOLUME on the remote control unit. Operations Use VOLUME + or VOLUME ­ to adjust the volume of the connected speakers. Press DISPLAY on the remote control unit. The currently selected input, screen size and refresh rates will be displayed for about 3 seconds. V O L U ME : 5 I NPUT 1 To mute the sound fH: fV: 3 1. 0 H z 64 0X 480 D O T BY D OT MUTING Note The displayed refresh rates may be slightly different from the actual values. Press MUTING on the remote control unit. Press MUTING again to restore the sound. Muting is automatically canceled about 8 minutes after the button is pressed, and the volume level is adjusted to the minimum level. Press VOLUME + or VOLUME ­ to adjust the volume at a desired level. 21 PRO-1000HD / PRO-800HD Operations Screen Size Selection This unit incorporates screen modes of various height and width ratios. For optimal viewing, we recommend that you select the screen mode that best matches the video source that you are viewing. Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer's intentions. During video signal input How the picture looks WIDE Suitable for when viewing news or sports programs. Movies or sports programs can be viewed with an expansive powerful image. [. . . ] 1 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ÷ Due to improvements, specifications and design are subject to change without notice. BNC jack (x5) 1 RGB signal (G ON SYNC compatible) RGB . . . TTL level /positive and negative polarity/ 75 or 2. 2 k (impedance switch) G ON SYNC . . . 1 Vp-p/75 /negative sync. 36 PRO-1000HD / PRO-800HD Additional Information Supplement 1 Resolution (Dot x Line) 640x400 -1/2: PRO-1000HD : Not available. [. . . ]