User manual PIONEER PRO-800HDI

[. . . ] PLASMA DISPLAY PRO-1000HDI PRO-800HDI Register Your Product on www. pioneerelectronics. com Operating Instructions Safety Precautions The following symbols are found on labels attached to the product. They alert the operators and service personnel of this equipment to any potentially dangerous conditions. WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCESSIBLE. CAUTION: WARNING This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage. WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. CAUTION This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death. Wash hands after handling. IMPORTANT NOTICE The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. i ii PRO-1000HDI / PRO-800HDI Safety Precautions IMPORTANT SAFETY INSTRUCTIONS READ INSTRUCTIONS -- All the safety and operating instructions should be read before the product is operated. [. . . ] Each time SET is pressed, the SIGNAL RANGE setting changes as shown: AUTO TYPE-2 TYPE-1 3 Press 5/ to select AUDIO SELECT. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L A UT O P OWER OF F C OL OR T E M P D I G I T A L NR H I GH C O N T R A S T V I D E O S I GNAL S I GNAL R A NGE A U D I O S E L E CT INPUT5 OPTION : I N P UT 5 : OF F : M I D DL E : L OW : OF F : AU T O : AU T O : AUTO AUTO: TYPE-1: TYPE-2: Note Select AUTO for normal picture set up. Select TYPE-1 to remove white glare in the picture when AUTO is set. Select TYPE-2 for too dark or distorted picture when AUTO is set. SELECT SET CHANGE MENU EXIT 4 Even when AUTO is selected, automatic switching may occur properly with someinput signals. In this event, select TYPE-1 or TYPE-2 manually in accordance with the actual signal input. Press SET to select the desired AUDIO SELECT setting. The unit has been factory set at the AUTO setting. Each time SET is pressed, the AUDIO SELECT setting changes as shown: AUTO ANALOG DIGITAL 5 Following completion of the setting, press MENU once again to return to the normal display. AUTO: Automatically identifies input audio signals. DIGITAL: Accept digital audio signals ANALOG: Accept analog audio signals Note Even when AUTO is selected, automatic switching may occur properly with someinput signals. In this event, select DIGITAL or ANALOG manually in accordance with the actual signal input. AUDIO SELECT This function allows you to switch the audio signal to automatic or manual when inputting the digital signal. Note AUDIO SELECT setting is possible only when INPUT5 is selected. 5 Following completion of the setting, press MENU once again to return to the normal display. 1 Press MENU to display the menu screen. The menu screen appears. MAIN MENU SCREEN : CO NT RA S T 0 : BR I GHT . 0 : CO LOR 0 : T I NT 0 : S H ARP 0 RE S E T PICTURE SET UP INPUT5 OPTION SELECT SET ENTER MENU EXIT 21 PRO-1000HDI / PRO-800HDI Setting Up the System Operations Selecting an Input Source This section explains the basic operation of this unit. Outlined on the following pages is how to turn the main power on and off, put this unit in the operation or standby mode and how to select connected components. 3 Press INPUT on the remote control unit or the main unit to select the input. Input changes each time the main unit's INPUT is pressed as follows. 3 INPUT1 3 INPUT2 3 INPUT3 INPUT4 2 INPUT5 2 Before you begin, make sure you have: · Made connections between this unit and AV components or personal computer as described in the section "Installation and Connections" starting on page 8. · Set up the on-screen menu to input signals from components connected to INPUT1 and INPUT2 as described in the section "Setting Up the System" on page 18. If no connections are made to these terminals, on-screen setup is not necessary. · When the menu screen is displayed, changing the signal input will cause the menu screen to turn off. · If the input computer signal is not supported by the display, the following message will be displayed: I NPUT 1 CA U T I O N U N S UP P O R T E D S I G N AL fH: fV: 7 7. 0 H z 1 15 2X 864 FUL L 2, 5 I NPUT 1 3 2, 5 3 CA U T I O N OU T OF R A N G E f H : 7 5. 0 H z ­­­­ FUL L 4 4 Main Unit Operating Panel Remote Control Unit Use VOLUME +/­ on the remote control unit to adjust the volume. If no audio connections are made to this unit, this step is not necessary. When viewing is finished, press STANDBY/ON to put the unit in standby mode. The STANDBY/ON indicator will blink and then remain lit (red) indicating that the standby mode is engaged. Operation is not possible while the STANDBY/ON indicator is blinking (red). Switch MAIN POWER on the main unit to the off position to turn the main power off. [. . . ] 1 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ÷ Due to improvements, specifications and design are subject to change without notice. BNC jack (x5) 1 RGB signal (G ON SYNC compatible) RGB . . . TTL level /positive and negative polarity/ 75 or 2. 2 k (impedance switch) G ON SYNC . . . 1 Vp-p/75 /negative sync. 38 PRO-1000HDI / PRO-800HDI Additional Information Supplement 1 Resolution (Dot x Line) 640x400 -1/2: PRO-1000HDI : Not available. [. . . ]