User manual PIONEER RS-232

[. . . ] RS-232 Command Reference Manual For PIONEER PDP-505CMX Plasma Display Panel January 2006 Document Version 1. 0 Product specifications and functions subject to change. Please check with your authorized Pioneer dealer or distributor. RS-232C Adjustment Mode 1. 0 RS-232C Adjustment Mode This display panel has an RS-232C terminal. It is possible to use a PC to make adjustments and settings. 1. 1 About the RS-232C Adjustment Mode 1) Adjustments in the RS-232C adjustment mode: · The adjustments are written to the same memory area as for the integrator mode. Refer to section 5. 4. 4, "PICTURE, White Balance and SCREEN Position Adjustment Values Memory Area Tables" (pg. [. . . ] Sets the SIGNAL FORMAT to VIDEO 525p or VIDEO 750p. SIZE: Displays the current sub screen input function. Returns the integrator PICTURE and WHITE BALANCE to the factory settings. Displays the current screen size setting. Sets the screen size to Dot by Dot or PARTIAL. Sets the screen size to FULL or FULL1080i. Adds n to the adjustment value (n = 1 to 9). SIZE. ¶ ¶ ¶ ¶ 11 RS-232C Adjustment Mode 1. 6 GET Commands What are GET commands?· GET commands are for outputting TXD such as adjustment data from the internal microcomputer of the plasma display to a PC. · Adjustment data and other information is output as ASCII code. Note Command names are given inside brackets < >. · Data output format STX (02hex) Data Data ···· Data Checksum ETX (03hex) Notes · A GET command is invalid when no ID is assigned to the set. · A GET command is invalid when a wildcard (*) is used as par of the ID when sending the command. 1) <GST> (GET STATUS) Order 1 2 3 4 5 6 Data Contents Display data Power data Input function data (main) Input function data (sub) Screen size data 2-screen display Size 3 Byte 3 Byte 3 Byte 3 Byte 1 Byte 1 Byte Remarks See below See below (The third character is sub input. ) Input data when GST is received (INPUT1 to 5 is displayed as IN1 to 5. ) Sub input data when GST is received Note 3) (INPUT 1 to 5 is displayed as IN1 to 5. ) See below 0: OFF (1 screen) 1: 2-SCREEN 2: PinP (lower right) 3: PinP (upper right) 4: PinP (upper left) 5: PinP (lower left) 6: PoutP 0: LOCK OFF 1: BUTTONS LOCK 2: IR LOCK 3: IR&BUTTONS LOCK 4: MEMORY LOCK (3-digit number) (Internal temperature: Reference value) °C Note 1) (External temperature: Reference value) °C Note 1) (3-digit number) Displays the time. 7 8 9 10 11 12 13 14 15 FUNCTIONAL LOCK data Dummy data Temperature data 2 Temperature data 3 Serial Dummy data Dummy data HOURMETER Check sum Display data 1 Byte 3 Byte 3 Byte 3 Byte 15 Byte 3 Byte 3 Byte 5 Byte 2 Byte First character Second character Third character First character Second character Power data Screen size data Generation data: 4 (fixed) Inch data: 4 (43 inch), 5 (50 inch) Destination data: M (fixed) Power state & signal state PN (POWER ON & normal signal input) PL (POWER ON & no input) PO (POWER ON & OUT OF RANGE signal input) SN (Normal standby) SW (Standby by POWER MANAGMENT) SS (Standby by SD or PD) Third character Sub input signal state during multi-screen display Note 2) N (Normal signal input) L (No input) O (OUT OF RANGE signal input) First character 0; Dot by Dot or PARTIAL 1; 4 : 3 2; FULL or FULL1080i 3; ZOOM 4;CINEMA 5;WIDE 8;FULL1035i 9; UNDERSCAN NOTE 1) During Standby and immediately after POWER ON, the proper value is not output. If this occurs, wait a moment after POWER ON then 'get' the data. The temperature data is output as a reference (the values are not guaranteed values). NOTE 2) During Standby and during 1-screen display, the unit outputs dummy data (symbol). NOTE 3) During Standby and during 1-screen display the unit outputs values stored in the product's memory. 12 RS-232C Adjustment Mode 2) <GPI> (GET PICTURE DATA: Gets integrator/PICTURE data. ) Order 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Data contents CONTRAST BRIGHTNESS C. DETAIL M (MAGENTA) H. ENHANCE V. ENHANCE COLOR TINT SHARPNESS Input function data (main) Screen size data Check sum Size 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 1 Byte 2 Byte Remarks # # # # # # # # Outputs dummy data for a video signal. # Outputs dummy data for a video signal. # · 7 and 8 output the same contents as GST items 3 and 5. · When the type of # signal is not set, dummy data is output. 3) <GWB> (GET WHITE BAL. data. ) Order 1 2 3 4 5 6 7 8 9 Data contents R. HIGH G. HIGH B. HIGH R. LOW G. LOW B. LOW Input function data (main) Screen size data Check sum Size 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 1 Byte 2 Byte Remarks # # # # # # · 7 and 8 output the same contents as GST items 3 and 5. · When the type of # signal is not set, dummy data is output. 4) <GPS> (GET POSITION DATA: Gets integrator/SCREEN data. ) Order 1 2 3 4 5 6 7 8 9 Data contents H. POSITION V. POSITION H. SIZE V. SIZE CLOCK PHASE Input function data (main) Screen size data Check sum Size 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 3 Byte 1 Byte 2 Byte Remarks # # # # Outputs dummy data for PC digital and Video signal. [. . . ] ¶ An invalid operation was attempted. Check the input signals, connections and settings. ¶ Turn the main power OFF, wait 1 or 2 minutes and turn the power ON again. If the problem still persists, remove the power plug from the outlet and contact a Pioneer service center or dealer. (): Numbers are displayed here. 19 Maintenance 1) Always unplug the power cord from the power outlet before performing maintenance. [. . . ]