User manual PIONEER S-DV131

[. . . ] 00 DVD/CD Receiver English XV-DV131 XV-DV232T Speaker System Deutsch Français S-DV131 S-DV232T Italiano Nederlands Español Operating Instructions 1 En Location: rear of the unit IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_En-A CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. [. . . ] When you load a disc containing this type of DivX VOD content, the remaining number of plays is shown on-screen and you then have the option of playing the disc (thereby using up one of the remaining plays), or stopping. If you load a disc that contains expired DivX VOD content (for example, content that has zero remaining plays), the message Rental Expired is displayed. If your DivX VOD content allows an unlimited number of plays, then you may load the disc into your player and play the content as often as you like, and no message will be displayed. 2 Press (cursor right) to change the speaker distance for the highlighted speaker. 3 Use the / (cursor up/down) to change the distance. · When you change the distance settings of the front left (L ) or front right (R) speakers, all the other speaker distances change relative to it. · Front left/right (L /R) speaker distances can be set from 30 cm to 9 m in 30 cm increments. · The center speaker (C) can be set from ­2. 1 m to 0 m relative to the front left/right speakers. · Surround left/right (SL /SR) speakers can be set from ­6. 0 m to 0 m relative to the front left/right speakers. 1 Español Note 1 Make sure to set them the same distance when using Front Surround (page 11). 23 En 05 Initial Settings menu · The subwoofer (SW) can be set from ­2. 1 m to 0 m relative to the front left/right speakers. 4 Press (cursor left) to go back to the speaker list if you want to modify another speaker, or press ENTER to exit the Speaker Distance screen. 24 En Other connections 06 Chapter 6 English Other connections Connecting auxiliary components This system has both stereo analog inputs and outputs. Use these to connect external components, such as your VCR, MD or CD-R recorder. Recording mode The Recording mode allows you to make surround-compatible analog recordings from the LINE (AUDIO OUT) jacks. 1 Dolby multichannel sources will be downmixed to stereo for improved playback with systems that can provide matrix-decoding (like Dolby Pro Logic). Deutsch Français 1 Connect the LINE (AUDIO IN) jacks to the analog outputs of an external playback component. Connect using RCA pin-plug stereo cables. 1 Press SOUND MODE. 2 Use / (cursor left/right) to select REC MODE then press ENTER . 3 Use / (cursor up/down) to select MODE ON or MODE OFF then press ENTER to confirm. · MODE ON ­ Multichannel sources are downmixed to stereo for recording (the same downmix is heard through the front speakers and the subwoofer). · MODE OFF ­ For regular multichannel playback through your speaker system (only the front left and right channels are output from the line output). Italiano 2 Connect the LINE (AUDIO OUT) jacks to the analog inputs of an external recording component. These include components such as a cassette deck, VCR, MD, or another recorder with analog inputs. Connect using RCA pin-plug stereo cables. Tape deck, etc. Nederlands AUDIO OUTPUT AUDIO INPUT Español T CB/ PB CR/ PR IN L LINE OUT L FRONT R L Y R AUDIO R SURROUND R L SPEAKERS XV-DV131/232T Note 1 · When Recording mode is on, most sound features cannot be used. The display will briefly blink REC MODE if you try and use a prohibited function while Recording mode is on. · When Recording mode is off, the audio from the LINE (AUDIO OUT) jacks may be interrupted, depending on the operation. · The Recording mode switches off if you change the input function (DVD/CD, TUNER, etc. ) or switch the power off. 25 En 06 Other connections Connecting external antennas For an external AM antenna, use 5­6 meters of vinyl-insulated wire and set up either indoors or outdoors. Leave the loop antenna connected. Outdoor antenna Connecting the S-video output If your TV has an S-video input, you can use this instead of the standard video output for a better quality picture. Indoor antenna (vinyl-coated wire) · Use an S-video cable to connect the SVIDEO OUT to an S-video input on your TV. Line up the small triangle above the jack with the same mark on the plug before plugging in. 5­6 m AM LOOP ANTENNA For an external FM antenna, Use a PAL connector to hook up an external FM antenna. TV S-VIDEO INPUT ANTENNA PAL connector VIDEO OUT S-VIDEO OUT COMPONENT VIDEO OUT CB/ PB IN CR/ PR LINE OUT L FRONT R L Y R AUDIO R SURROUND R VIDEO XV-DV131/232T 26 En Other connections 06 Connecting using the component video output If your TV has component video inputs, you can use these instead of the standard video output to connect this system to your TV. 1 This should give you the best quality picture from the three types of video output available. Important · If you connect a TV that is not compatible with a progressive scan signal and switch the system to progressive, you will not be able to see any picture at all. In this case, press STANDBY/ON to put the system in standby, then press SHIFT+SYSTEM SETUP , use the / (cursor left/right) button to select INTER L . Press ENTER to set to interlace and switch the system back on. English Deutsch · Use a component video cable to connect the COMPONENT VIDEO OUT to a set of component inputs on your TV. Français Compatibility of this player with progressive-scan and high-definition TVs. COMPONENT INPUT TV This player is compatible with progressive video Macro Vision System Copy Guard. 2 This system is compatible with the following Pioneer displays and monitors: Plasma display (Taiwanese model ) PDP-502MX, PDP-503HDG, PDP-433HDG, PDP-5040HD, PDP-4340HD, PDP-505HDG, PDP-435HDG Projection monitor receiver (Taiwanese model) SD-532HD5, SD-533HD5 Plasma display (All other models) PDP-503HDG, PDP-433HDG, PDP-504HDG, PDP-434HDG, PDP-505HDG, PDP-435HDG Italiano Nederlands COMPONENT VIDEO OUT VIDEO OUT S-VIDEO OUT VIDEO CB/ PB IN CR/ PR LINE OUT L Y R AUDIO Español XV-DV131/232T About progressive scan video Compared to interlace video, progressive scan video effectively doubles the scanning rate of the picture, resulting in a very stable, flickerfree image. Progressive scan video is available only from the component video output. Note 1 The component video output is switchable between interlaced and progressive formats. 2 Consumers should note that not all high-definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the `standard definition' output (Interlace). [. . . ] Closed-box bookshelf type (magnetically shielded) System . 0. 6 kg · Subwoofer Enclosure. 16 cm cone type Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", and the double-D symbol are trademarks of Dolby Laboratories. "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc. 42 En Additional information 08 Wall-mounting the front and surround speaker system Attaching the brackets · Make sure to tighten the supplied screw as securely as possible when attaching the bracket to the back of the speaker. · Please do not attach the brackets to the center speaker. [. . . ]