User manual PIONEER SC-LX75

[. . . ] SC-LX85 SC-LX7 5 IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT: THE MOULDED PLUG This appliance is supplied with a moulded three pin mains plug for your safety and convenience. [. . . ] If you don't plan to use the MULTI-ZONE feature for a while, turn off the power in both the sub and main rooms so that this receiver is in standby. Button(s) MUTE <a> What it does Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound). 3 Select the input signal according to the signal to be recorded. Use the remote control's SIGNAL SEL button. % Set the remote control to the receiver operation mode, then press SLEEP repeatedly to set the sleep time. 30 min Off 60 min 90 min 4 Prepare the recorder. a You can only use this button when Speaker System is set to 7. 1ch + ZONE 2. Making an audio or a video recording You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV). Keep in mind you can't make a digital recording from an analog source or vice-versa, so make sure the components you are recording to/from are hooked up in the same way (see Connecting your equipment on page 14 for more on connections). The receiver's volume, Audio parameters (the tone controls, for example), and surround effects have no effect on the recorded signal. Some digital sources are copy-protected, and can only be recorded in analog. Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use the same type of video cable for connecting your recorder as you used to connect your video source (the one you want to record) to this receiver. For example, you must connect your recorder using Component video if your source has also been connected using Component video. Insert a blank tape, MD, video etc. into the recording device and set the recording levels. Refer to the instructions that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level automatically-check the component's instruction manual if you're unsure. 5 Start recording, then start playback of the source component. MULTI-ZONE remote controls The following table shows the possible MULTIZONE remote controls: SC-LX85: !Set the MULTI-ZONE operation switch to ZONE 2 or ZONE 3 to operate the corresponding zone. Press the remote control's ZONE 2 or ZONE 3 to operate the corresponding zone. Button(s) u INPUT SELECT Input function buttons SC-LX85: VOL +/­ <a> SC-LX75: MASTER VOLUME +/­ <a> Use to set the listening volume in the sub zone. !You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle through the sleep options again. If any zone is on, the sleep timer continues functioning. Reducing the level of an analog signal The input attenuator lowers the input level of an analog signal when it's too strong. You can use this if you find that the OVER indicator lights often or you can hear distortion in the sound. The attenuator isn't available with digital sources, or when using the Stream Direct (ANALOG DIRECT) modes. Dimming the display You can choose between four brightness levels for the front panel display. Note that when selecting sources, the display automatically brightens for a few seconds. What it does Switches on/off power in the sub zone. Use to select the input function in the sub zone. Use to select the input function directly (this may not work for some functions) in the sub zone. % Set the remote control to the receiver operation mode, then press A. ATT to switch the input attenuator on or off. % Set the remote control to the receiver operation mode, then press DIMMER repeatedly to change the brightness of the front panel display. !You can also choose to turn the display off. In this case, the FL OFF indicator lights. Using the sleep timer The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. [. . . ] 1 AM loop antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Warranty card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Power cord CD-ROM (AVNavigator) Quick start guide Digital In/Out Section HDMI terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-pin (Not DVI) HDMI output type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 55 mA USB terminal . . . . . . . . . . . . USB2. 0 Full Speed (Type A) iPod terminal . . . . . . . . . [. . . ]