User manual PIONEER SC-LX77-K

[. . . ] Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer. [. . . ] Use to set the listening volume in the currently selected sub zone. IN CONTROL Pioneer component IN OUT LAN (10/100) COAXIAL ASSIGNABLE IN 1 (DVD) 12 V TRIGGER (OUTPUT 12V TOTAL 50mA MAX) 1 IN 1 IN (DVD) (VIDEO1) IR IN 1 IN 2 OUT HDMI BD IN IN 2 (CD) 2 PR PB Y ZONE 2 OUT R PR L ZONE 2 OUT IN 3 (DVR2) IN 1 IR IN 1 IN 2 OUT ZONE 3 OUT PHONO IN SIGNAL GND L CD IN CD-R OUT IN 1 (TV/SAT) IN 2 (DVR1) IN 3 (VIDEO1) SIGNAL GND IN 2 L R IN IN 3 CONTROL IN 4 (CD-R) ASSIGNABLE ZONE3/ SOURCE OUT OUT R IN ASSIGNABLE 1 - 3 OUT 1 (HDMI CTRL) CONTROL SOURCE OUT OUT 2 RS-232C OUT OPTICAL DIGITAL IR receiver 2 Connect the IR IN jack of another component to the IR OUT jack on the rear of this receiver to link it to the IR receiver. Please see the manual supplied with your IR receiver for the type of cable necessary for the connection. · If you want to link a Pioneer component to the IR receiver, see Operating other Pioneer components with this unit's sensor on page 106 to connect to the CONTROL jacks instead of the IR OUT jack. Note 1 The tuner cannot be tuned to more than one station at a time. Therefore, changing the station in one zone also changes the station in the other zone. Please be careful not to change stations when recording a radio broadcast. 2 The volume levels of the main and sub zones are independent. 3 · You won't be able to switch the main zone off completely unless you've switched off the MULTI-ZONE control first. · If you don't plan to use the MULTI-ZONE feature for awhile, turn off the power in both the sub and main rooms so that this receiver is in standby. 4 · Remote operation may not be possible if direct light from a strong fluorescent lamp is shining on the IR receiver remote sensor window. · Note that other manufacturers may not use the IR terminology. Refer to the manual that came with your component to check for IR compatibility. 2 To switch SR+ mode on/off, set the operation selector switch to RCV, then press SR+. The front panel display shows SR+ ON or SR+ OFF. · The automatic video input switching and the automatic volume muting features are enabled separately; see SR+ Setup for Pioneer flat screen TVs on page 93. 69 En 09 Other connections Connecting a PC for Advanced MCACC output When using the Acoustic Calibration EQ Professional (see page 50) to calibrate the reverb characteristics of your listening room, you can graphically check the results on your computer connected to this receiver. Also, when the Full Band Phase Control function is activated, you can visually check the calibrated characteristics of group delay of the speakers and the corrected characteristics of group delay processed by the exclusive correction filter by installing the corresponding PC application on your computer. Use a commercially-available RS-232C cable to connect the RS-232C jack on your computer to the 9-pin RS-232C jack on the back panel of this receiver (the cable must be cross type, female­female). The software to output the results is available from the support area of the Pioneer website (http:// www. pioneer. eu). Instructions for using the software are also available here. If you have any questions about the software, please contact the Pioneer Service Center specified on your warranty card. Please make sure your system meets the following requirements: · Operating system must be Microsoft Windows® XP (Service Pack 2) or Windows® 2000. · CPU must be at least Pentium 3 / 300 MHz or AMD K6 / 300 MHz (or equivalent) with at least 128 MB of memory, and your monitor must be able to display a minimum resolution of 800x600. · An RS-232C port connector is necessary for graphical output. [. . . ] It is also possible to play contents stored on iPod and USB devices. Also, you can listen to the Internet radio stations. · Dolby Digital and DTS decoding, including Dolby Digital EX, Dolby Pro Logic IIx, DTS 96/24, DTS-ES, Dolby Digital Plus, Dolby TrueHD, DTS-EXPRESS and DTS-HD Master Audio Dolby Digital and DTS decoding brings theater sound right into your home with up to six channels of surround sound, including a special LFE (Low Frequency Effects) channel for deep, realistic sound effects. The built-in Dolby Pro Logic IIx and DTS Neo:6 decoders not only provide full surround sound decoding for Dolby Surround sources, but will also generate convincing surround sound for any stereo source. [. . . ]