User manual PIONEER SX-636 service manual

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_En-A WARNING This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain D3-4-2-1-3_A_En or moisture. WARNING Before plugging in for the first time, read the following section carefully. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e. g. , 230V D3-4-2-1-4_A_En or 120V) written on the rear panel. Operating Environment Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D3-4-2-1-7c_A_En WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the D3-4-2-1-7a_A_En equipment. This product complies with the Low Voltage Directive (73/23/EEC, amended by 93/68/EEC), EMC Directives (89/336/EEC, amended by 92/31/EEC and D3-4-2-1-9a_En 93/68/EEC). CAUTION This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. [. . . ] The only exception to this is when the picture quality is set to LPCM, in which case you do need to select the audio channel before recording. AUDIO Note 1 Audio is recorded in 16-bit Linear PCM format, video is recorded at XP quality. When recording a bilingual broadcast, select which audio channel to record (see Bilingual Recording on page 133). 82 En Recording 07 AUDIO 6 MAIN SUB + If you're recording from the D. TV tuner, select the audio language to record. · You may also be able to set which subtitle language to record; use SUBTITLE to select. REC Pause Live TV HDD ì Start recording. 7 If you want to set a recording end time, press the ì REC button repeatedly. The recording time increases in 30 minute increments, up to a maximum of six hours. The time the recording will end is shown on-screen and in the front panel display. When the recording ends, the recorder automatically switches into standby if no other operation is being performed. The Pause Live TV feature lets you effectively pause a TV program you're watching. When you're ready to resume watching, just press the PLAY button. Setting up for Pause Live TV You can use the Pause Live TV feature with an AV Linkcompatible TV connected using a SCART cable (see TV tuner setup for Pause Live TV below), or using this recorder's internal tuner (see Using the recorder's internal tuner for Pause Live TV below). · To cancel the set recording time, press ì REC. · If you want to pause recording at any time1, press PAUSE. Press again to restart the recording (If recording to the HDD, DVD-RAM or in VR mode, a new chapter is started after recording restarts). STOP REC TV tuner setup for Pause Live TV To use this feature with an external TV tuner, the recorder must be connected to your TV using a SCART cable, and the AV Link setting (page 138) should be set to This Recorder Only. 2 See also Pause Live TV on page 129 for more on this. In order to use Pause Live TV, make the following connections and settings. The operation is slightly different depending on the viewing source. See the Operation table below for details. Tip · When the Pause Live TV setting (see page 129) is set to TV's Tuner, you can press PAUSE LIVE TV while the recorder is in standby to switch on and immediately start recording. When set to Recorder's Tuner, it is not possible to use the Pause Live TV feature from standby. · After pressing PAUSE LIVE TV, it will take at least 10 seconds for the picture to change (during this time, all controls except the power button are inoperative). (Note that startup from standby is not possible if you have selected Recorder's Tuner in Pause Live TV on page 129. ) · Please note that you can't record from another component (VCR, etc. ) that is connected by a SCART cable to the AV2(INPUT 1/DECODER) connector using the Pause Live TV feature. 2 Select `Initial Setup' > `Basic' > `Pause Live TV' > `Recorder's Tuner'. See Pause Live TV on page 129 to do this. You can record the channel selected on the recorder. Using Pause Live TV PAUSE LIVE TV 1 Start recording the current TV channel. Recording continues with playback paused. · Note that it may take up to 10 seconds for recording to start. PLAY 2 Press to start playback. You can also use the scan buttons ( / ), pause ( PAUSE) and stop ( STOP)--all without affecting the recording. Operation table Viewing source TV built-in analog tuner TV/DVD mode of DVR TV DVR source ­ Pause Live TV function button Pause Live TV Condition Preset channel of DVR and TV are matched after downloading from TV Direct TV recording*1 Preset channel of DVR and TV are NOT matched after downloading from TV. [. . . ] AV connector (AV1), RCA jack (Output) S-Video input . . AV2 (Input 1), Input 2 (front), Input 3 (rear) Y (luminance) - Input level . . AV connector (Input 1), 4 pin mini DIN (Input 2, Input 3) S-Video output . . AV1, Output Y (luminance) - Output level . [. . . ]