User manual PIONEER VSX-1120-K

[. . . ] AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-1120-K Register your product at http://www. pioneerelectronics. com (US) http://www. pioneerelectronics. ca (Canada) · Protect your new investment The details of your purchase will be on file for reference in the event of an insurance claim such as loss or theft. · Receive free tips, updates and service bulletins on your new product · Improve product development Your input helps us continue to design products that meet your needs. · Receive a free Pioneer newsletter Registered customers can opt in to receive a monthly newsletter. Operating Instructions IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_A1_En 1) 2) 3) 4) 5) 6) 7) Read these instructions. [. . . ] 1 Turn on the computer and launch the Internet browser. 2 In the address bar on the browser, enter the IP address assigned to this receiver. For example, if the IP address of this receiver is "192. 168. 0. 2", enter "http://192. 168. 0. 2/". When the connection is made with the receiver, a Top Menu will be displayed. This receiver's IP address can be found in the `IP address, Proxy' menu (page 81). 3 Once the Top Menu is displayed, click the button for the zone you want to operate. 4 Operate from the screen for the individual zone. · Even when the receiver is in the standby mode, it can be turned on using the Web Control function. For details, see Network Standby on page 82. Top Menu Checking your system settings Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset. 1 Press RECEIVER , then press STATUS to check the system settings. The front panel display shows each of the following settings for three seconds each: Input function, Sampling Frequency, MCACC preset, ZONE 2 input and HDMI OUT. 2 When you're finished, press STATUS again to switch off the display. Resetting the system Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. · Disconnect the iPod and USB memory device from the receiver beforehand. 1 Switch the receiver into standby. Web Control Main ZONE POWER ON OFF ZONE 2 VOLUME -60. 0dB ZONE 3 MUTE INPUT SELECT DVD 2 While holding down ENTER on the front panel, press STANDBY/ON. 3 Select `RESET' using PRESET /, then press ENTER on the front panel. OK appears in the display to indicate that the receiver has been reset to the factory default settings. · Note that all settings will be saved, even if the receiver is unplugged. LISTENING MODE AUTO SURR/ALC/ STREAM DIRECT STEREO HOME THX STANDARD SURROUND ADVANCED SURROUND STEREO 60 En Using other functions 08 Default system settings Setting Digital Video Conversion SPEAKERS Speaker System Speaker Setting Front Center FH/FW Surr SB SW Surround Position Crossover X-Curve THX Audio Setting DIMMER Network Standby Inputs See Input function default and possible settings on page 38. HDMI HDMI Audio Control Control Mode DIsplay Power Off Amp ON ALL YES Default ON A Normal (SB/FH) SMALL SMALL SMALL SMALL SMALLx2 YES IN REAR 80 Hz OFF 4 ft< Brightest OFF Setting DSP Power On Level Volume Limit Mute Level Phase Control Sound Retriever Default LAST OFF FULL ON iPod/USB, INTERNET ON RADIO, ADAPTER PORT function Other functions OFF 0. 0 frame CH1 AUTO 0 dB 0 dB OFF OFF Sound Delay Dual Mono DRC SACD Gain LFE Attenuate Auto delay Digital Safety Effect Level 2 PL II Music Options Neo:6 Options All Inputs ExtendedStereo Other modes Center Width Dimension Panorama Center Image Listening Mode (2 ch/multi ch) 90 50 3 0 OFF Neo:6 MUSIC: 3 Neo:6 CINEMA: 10 AUTO SURROUND Listening Mode (HP) STEREO See also Setting the Audio options on page 55 for other default DSP settings. MCACC MCACC Position Memory Channel Level (M1 to M6) Speaker Distance (M1 to M6) Standing Wave (M1 to M6) EQ Data (M1 to M6) M1: MEMORY 1 0. 0 dB 10. 00 ft ATT of all channels/ 0. 0 dB filters SWch Wide Trim All channels/bands EQ Wide Trim 0. 0 dB 0. 0 dB 0. 0 dB 61 En 09 Controlling the rest of your system Chapter 9: Controlling the rest of your system Operating multiple receivers Up to four receivers can be operated discretely using this receiver's remote control when using multiple receivers, provided they are of the same model as this receiver. The receiver to be operated is switched by inputting the preset code to set the remote control setting. · Set the remote modes on the receivers before using this function (see Remote Control Mode Setup on page 83). [. . . ] The original container is ideal for this purpose. Include your name, address and telephone number where you can be reached during business hours. On all complaints and concerns in the U. S. A. call Customer Support at 1-800-421-1404, or, in Canada, call Customer Satisfaction at 1-877-283-5901. IN THE U. S. A. [. . . ]