User manual PIONEER VSX-32

[. . . ] Operating Instructions VSX-33 audio/video multi-channel receiver VSX-32 IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_A1_En 1) 2) 3) 4) 5) 6) 7) Read these instructions. [. . . ] Use to select the input function in the sub zone. Use to select the input function directly (this may not work for some functions) in the sub zone. Use to set the listening volume in the sub zone. a Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound). a 4 Prepare the recorder. into the recording device and set the recording levels. Refer to the instructions that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level automatically--check the component's instruction manual if you're unsure. 5 Start recording, then start playback of the source component. Reducing the level of an analog signal The input attenuator lowers the input level of an analog signal when it's too strong. You can use this if you find that the OVER indicator lights often or you can hear distortion in the sound. 2 · Press RECEIVER , then press A. ATT to switch the input attenuator on or off. a. You can only use this button when Speaker System is set to ZONE 2. Using the sleep timer Making an audio or a video recording You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV). 1 Keep in mind you can't make a digital recording from an analog source or vice-versa, so make sure the components you are recording to/from are hooked up in the same way (see Connecting your equipment on page 15 for more on connections). Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use the same type of video cable for connecting your recorder as you used to connect your video source (the one you want to record) to this receiver. For example, you must connect your recorder using Component video if your source has also been connected using Component video. Use the input function buttons (or INPUT SELECT). 2 Prepare the source you want to record. Tune to the radio station, load the CD, video, DVD etc. 3 Select the input signal according to the signal to be recorded. Use the remote control's SIGNAL SEL button. The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. Use the remote control to set the sleep timer. · Press RECEIVER , then press SLEEP repeatedly to set the sleep time. 30 min Off 60 min 90 min · You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle through the sleep options again. 3 Dimming the display You can choose between four brightness levels for the front panel display. Note that when selecting sources, the display automatically brightens for a few seconds. · Press RECEIVER , then press DIMMER repeatedly to change the brightness of the front panel display. Note 1 · The receiver's volume, Audio parameters (the tone controls, for example), and surround effects have no effect on the recorded signal. · Some digital sources are copy-protected, and can only be recorded in analog. [. . . ] We do this by focusing on three important steps: 1 Designing with carefully selected components so as to transmit the original soundtrack accurately 2 Allowing for customized acoustic calibration according to any listening area 3 Tuning that transmits soul This product includes FontAvenue® fonts licenced by NEC corporation. FontAvenue is a registered trademark of NEC Corporation We Want You Listening For A Lifetime Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries Association's Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise. This list of sound levels is included for your protection. [. . . ]