User manual PIONEER VSX-4800

[. . . ] RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. ATTENTION ­ POUR PREVENIR LES CHOCS ELECTRIQUES, NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR, UNE PRISE DE COURANT, OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE D2-4-4-1_EF A DECOUVERT. IMPORTANT NOTICE ­ THE SERIAL NUMBER FOR THIS EQUIPMENT IS LOCATED IN THE REAR. PLEASE WRITE THIS SERIAL NUMBER ON YOUR ENCLOSED WARRANTY CARD AND D1-4-2-6-1_En KEEP IN A SECURE AREA. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] You will return to the Manual MCACC setup menu. 2 Select which method you would like to use to adjust the overall frequency balance. It is best to choose whichever one you copied to the custom setting in Copying your Acoustic Calibration EQ settings above. 3e. EQ CUSTOM1 Adjust Test Tone Type [ ALL CH ADJUST ] Checking your Acoustic Calibration EQ settings Enter : Next Return : Cancel After you have completed an automatic or manual Acoustic Calibration EQ adjustment, you can check the ALL CH ADJUST, FRONT ALIGN and custom settings using the on-screen display. 1 Select `EQ Data Check' from the Manual MCACC setup menu. 3. MANUAL MCACC · ALL CH ADJUST ­ All the speakers can be set independently so no special weighting is given to any one channel. When adjusting, test tones will sound for each individual channel. · FRONT ALIGN ­ Speakers are set in accordance with the front speaker settings. The sound of the test tone will alternate between the left front (reference) speaker and the target speaker. [ [ [ [ [ [ [ a . Fine Ch Level b . Fine Ch Distance c . EQ AUTO Setting d . EQ Data Copy e . EQ CUSTOM1 Adjust f . EQ CUSTOM2 Adjust g . EQ Data Check ] ] ] ] ] ] ] 44 En The System Setup menu 06 2 Select the setting you want to check. 3g. EQ Data Check Type [ ALL CH ADJUST ] Ch [ Left EQ] 40Hz 125Hz 250Hz 4kHz 13kHz TRIM : : : : : : 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB 0. 0dB Manual speaker setup This receiver allows you to make detailed settings to optimize the surround sound performance. You only need to make these settings once (unless you change the placement of your current speaker system or add new speakers. ). These settings are designed to fine-tune your system, but if you're satisfied with the settings made in Automatically setting up for surround sound (MCACC) on page 11, it isn't necessary to make all of these settings. Caution · The test tones used in the System Setup are output at high volume (the volume increases to 0db automatically). · If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal. · If you're using a THX speaker setup, confirm that all speakers are set to SMALL. 2 Choose the set of speakers that you want to set then select a speaker size. 4a. Speaker Setting Front [ LARGE ] Center [ SMALL ] Surround [ SMALL ] Surr Back [ SMALLx2 ] Sub Woofer [ YES ] (THX Speaker:SMALL) Use / (cursor left/right) to select the size (and number) of each of the following speakers: · Front ­ Select LARGE if your front speakers reproduce bass frequencies effectively, or if you didn't connect a subwoofer. Select SMALL to send the bass frequencies to the subwoofer. · Center ­ Select LARGE if your center speaker reproduces bass frequencies effectively, or select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn't connect a center speaker, choose NO (the center channel is sent to the front speakers). · Surround ­ Select LARGE if your surround speakers reproduce bass frequencies effectively. Select SMALL to send bass frequencies to the other speakers or subwoofer. If you didn't connect surround speakers choose NO (the sound of the surround channels is sent to the front speakers or a subwoofer). · Surr Back ­ Select the number of surround back speakers you have (one, two or none). Select LARGE if your surround back speakers reproduce bass frequencies effectively. [. . . ] 15. 4 kg (34 lb) Audio Section Input (Sensitivity/Impedance) LINE. . 5 Hz to 100, 000 Hz dB Output (Level/Impedance) REC . +4/+2 dB (100Hz/10 kHz) (at volume position ­40 dB) Signal-to-Noise Ratio (IHF, short circuited, A network) LINE. 103 dB Signal-to-Noise Ratio [EIA, at 1W (1kHz)] LINE. [. . . ]