User manual PIONEER VSX-519V-S

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] If the component turns ON or OFF, you have entered the proper code. If the component does not turn ON or OFF and there is more than one setup code, press @ or # to select another code in step 3 or try inputting another code (starting again from step 2). Some manufacturers use several sets of remote control signals and the first code may not correspond to your component. Set up dB dB dB dB Repeat steps 2 through 4 to assign preset codes for as many components as necessary. 5 Press REMOTE SET UP to exit the preset mode. The remote control returns to the previous operation mode. · When operating a PIONEER'S DVD/LD player, set the manufacturer code to "111" in the preset mode. · All codes enrolled in the manufacturer code list can be set even if a code is not displayed. · If no commands are entered the receiver automatically exits the preset code mode after 20 seconds. 21 Preparations Clearing the Remote Control Settings Clears all presets and restores factory default settings. Î MULTI CONTROL DVD/LD TV/SAT VCR/DVR CD LED CD-R/ RECEIVER TUNER TAPE/MD TV CONT Press REMOTE SET UP and 0 at the same time for more 3 seconds. The LED display at the top of the remote control will blink. After blinking three times, all the settings will be canceled. 2 DSP MODE MIDNIGHT 5. 1CH 1 2 3 4 CHANNEL TEST SELECT TONE ATT SIGNAL SELECT 5 9 6 0 FUNC 7 EFFECT 8 ENTER CHANNEL LEVEL 10 CH VOL TV CONTROL FQ ST ENTER ST DISC 0 VOL MENU FQ TOP MENU SOURCE CLASS MPX BAND 7 D. ACCESS 8 4 3 ¢ CHANNEL 1 ¡ LOUDNESS FUNCTION MUTING FL REMOTE MASTER RECEIVER DIMMER SETUP VOLUME AUDIO/VIDEO PRE-PROGRAMMED REMOTECONTROLUNIT REMOTE SET UP Direct Function The direct function is a useful feature which allows you keep the receiver in one function (for example, CD) while putting the remote control in a different function. This could let you, for example, use the remote control to set up and listen to a CD on the receiver and then use the remote control to rewind a tape in your VCR while you continue to listen to your CD player. When the DIRECT function is ON any MULTI CONTROL button you press will change the function of both the receiver and the remote control. When you turn the DIRECT function OFF, you can operate the remote control without effecting the receiver. Thus you could switch the remote control the VCR and operate that component while the receiver plays a different component. MULTI CONTROL DVD/LD TV/SAT VCR/DVR CD CD-R/ RECEIVER TUNER TAPE/MD TV CONT 2 2 DSP MODE MIDNIGHT 5. 1CH 1 2 3 4 CHANNEL TEST SELECT TONE ATT SIGNAL SELECT 3 1 To turn the DIRECT funtion OFF (the default setting is ON), press REMOTE SET UP and number button 3 at the same time. MIDNIGHT (see page 31) Use to put receiver in MIDNIGHT mode. To use first press the RECEIVER button then operate this button. 5. 1 CH (see page 30) When the DVD/LD or DVD 5. 1 CH function is selected each press switches the DVD/LD input between DVD/LD and DVD 5. 1 CH. To use first press the RECEIVER button then operate this button. CHANNEL SELECT (see page 19-note) Use to slect a speaker when setting up the surround sound of the receiver. To use first press the RECEIVER button then operate this button. TEST TONE (see page 19) Use to sound the TEST TONE when setting up the surround sound of the receiver. To use first press the RECEIVER button then operate this button. Operation 2 RECEIVER button (see page 14) Use this button when setting up the surround sound for the receiver. 3 NUMBER/MODE buttons (see pages 33, 34) Use the number buttons to select the radio frequency in tuner DIRECT ACCESS mode or the tracks in CD, DVD mode etc. Also, buttons marked with the following names have special functions. If you try to use one of these functions but he display flashes it means that function cannot be used int he current mode (for example DSP modes cannot be used when 5. 1 CH setting is on). 2 (see pages 27, 29) Use to put receiver in DOLBY DIGITAL and DTS modes. [. . . ] 1 Vp-p/75 Frequency Response VCR/DVR, MONITOR +0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hz to 7 MHz ­3 dB Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB Cross Talk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 dB 44 R O NI C IND U ST RIES S SO CIAT IO N EST 1924 · EIA We Want You We Want You Listening For A Lifetime Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. [. . . ]